/*
 * Copyright (C) 2016 Icenowy Zheng <icenowy@aosc.xyz>
 *
 * This file is dual-licensed: you can use it either under the terms
 * of the GPL or the X11 license, at your option. Note that this dual
 * licensing only applies to this file, and not this project as a
 * whole.
 *
 *  a) This file is free software; you can redistribute it and/or
 *     modify it under the terms of the GNU General Public License as
 *     published by the Free Software Foundation; either version 2 of the
 *     License, or (at your option) any later version.
 *
 *     This file is distributed in the hope that it will be useful,
 *     but WITHOUT ANY WARRANTY; without even the implied warranty of
 *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 *     GNU General Public License for more details.
 *
 * Or, alternatively,
 *
 *  b) Permission is hereby granted, free of charge, to any person
 *     obtaining a copy of this software and associated documentation
 *     files (the "Software"), to deal in the Software without
 *     restriction, including without limitation the rights to use,
 *     copy, modify, merge, publish, distribute, sublicense, and/or
 *     sell copies of the Software, and to permit persons to whom the
 *     Software is furnished to do so, subject to the following
 *     conditions:
 *
 *     The above copyright notice and this permission notice shall be
 *     included in all copies or substantial portions of the Software.
 *
 *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
 *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
 *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
 *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
 *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
 *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
 *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
 *     OTHER DEALINGS IN THE SOFTWARE.
 */

/dts-v1/;
#include "sun8i-v3s.dtsi"
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/input/input.h>

/ {
	model = "Lichee Pi Zero";
	compatible = "licheepi,licheepi-zero", "allwinner,sun8i-v3s";

	aliases {
		serial0 = &uart0;
		ethernet0 = &emac;
	};

	chosen {
		stdout-path = "serial0:115200n8";

		fb0: framebuffer@0 {
			compatible = "allwinner,simple-framebuffer", "simple-framebuffer";
			allwinner,pipeline = "de0-lcd0";
			clocks = <&ccu CLK_BUS_TCON0>, <&display_clocks 0>, <&display_clocks 6>, <&ccu CLK_TCON0>;
			status = "disabled";
		};

	};

	leds {
		status = "disabled";
	};

	/*backlight: backlight {
	        compatible = "pwm-backlight";
	        pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
	        brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
	        default-brightness-level = <50>;
	        enable-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>;  //PB4 PWM
	    };*/
	
	    panel: panel {
	        compatible = "qiaodian,qd43003c0-40", "simple-panel";
	        #address-cells = <1>;
	        #size-cells = <0>;
			enable-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>;//使能引脚 PB4脚为高使能 这里为pwm信号

	        // power-supply = <&reg_vcc3v3>;
	        // enable-gpios = <&axp_gpio 0 GPIO_ACTIVE_HIGH>; /* AXP GPIO0 */
	        //backlight = <&backlight>;
	
	        port@0 {
			reg = <0>;
			#address-cells = <1>;
			#size-cells = <0>;

			panel_input: endpoint@0 {
				reg = <0>;
				remote-endpoint = <&tcon0_out_lcd>;
			};
		};

    	};
};
&spi0 {
	
	status = "okay";
	flash@0 {
	    #address-cells = <1>;
	    #size-cells = <1>;
	    compatible = "jedec,spi-nor";
	    reg = <0>;
    		spi-max-frequency = <50000000>;
	 partitions {
	      compatible = "fixed-partitions";
	      #address-cells = <1>;
	      #size-cells = <1>;
	
	      partition@0 {
	        label = "u-boot";
	        reg = <0x000000 0x100000>;
	        read-only;
	      };
	
	      partition@100000 {
	        label = "dtb";
	        reg = <0x100000 0x10000>;
	        read-only;
	      };
	
	      partition@110000 {
	        label = "kernel";
	        reg = <0x110000 0x400000>;
	        read-only;
	      };
	
	      partition@510000 {
	        label = "rootfs";
	        reg = <0x510000 0xAF0000>;
	      };
	      };
    };
};
&emac {
	status = "okay";
};
&ehci0 {
	status = "okay";
};

&mmc0 {
	pinctrl-0 = <&mmc0_pins_a>;
	pinctrl-names = "default";
	broken-cd;
	bus-width = <4>;
	vmmc-supply = <&reg_vcc3v3>;
	status = "okay";
};

&i2c0 {
	status = "okay";

	ns2009: ns2009@48 {
		compatible = "nsiway,ns2009";
		reg = <0x48>;
	};
};

&ohci0 {
	status = "okay";
};

&uart0 {
	pinctrl-0 = <&uart0_pins_a>;
	pinctrl-names = "default";
	status = "okay";
};

&uart1{
	pinctrl-0 = <&uart1_pins_a>;
	pinctrl-names = "default";
	status = "okay";
};

&uart2{
	pinctrl-0 = <&uart2_pins_a>;
	pinctrl-names = "default";
	status = "okay";
};

&codec {
	allwinner,audio-routing =
		"Headphone", "HP",
		"Headphone", "HPCOM",
		"MIC1", "Mic",
		"Mic",  "HBIAS";
	status = "okay";
};

&usb_otg {
	dr_mode = "host";
	status = "okay";
};

&usbphy {
	usb0_id_det-gpio = <&pio 5 6 GPIO_ACTIVE_HIGH>;
	status = "okay";
};
/*
&pwm {
    status = "okay";
};
*/
&de {
    status = "okay";
};

&tcon0 {
    pinctrl-names = "default";
    pinctrl-0 = <&lcd_rgb666_pins>;
    status = "okay";
};

&tcon0_out {
    tcon0_out_lcd: endpoint@0 {
        reg = <0>;
        remote-endpoint = <&panel_input>;
    };
};