WhyCan Forum

本站无需注册,无需积分,无需回复可下载所有资料,如果真的喜欢小站,请您注册之后请至少回复一个帖子激活Id,谢谢支持! 站长QQ: 516333132 (挖坑网/填坑网) admin@whycan.cn

您尚未登录。

#1 2019-05-16 17:58:23

MrJacky
会员
注册时间: 2019-02-26
累计积分: 8

全志A83T无法进系统问题

在A83T平台接8G大小的emmc烧录完后,系统不能启动。日志如附件,求大神帮忙看下啥问题。谢谢!

离线

#2 2019-05-16 17:59:42

晕哥
Administrator
注册时间: 2017-09-06
累计积分: 6,733

Re: 全志A83T无法进系统问题

附件右下角有个插入的图标,按一下。

离线

#3 2019-05-16 18:07:29

MrJacky
会员
注册时间: 2019-02-26
累计积分: 8

Re: 全志A83T无法进系统问题

离线

#4 2019-05-16 18:33:06

晕哥
Administrator
注册时间: 2017-09-06
累计积分: 6,733

Re: 全志A83T无法进系统问题

[BEGIN] 2019/5/16 9:53:28
HELLO! BOOT0 is starting!
boot0 version : 4.2.0
boot0 commit : c7427fafe51714aab06c0c1b92b2eb684e52992d
 
rtc[1] value = 0x00010000
rtc[2] value = 0x00020000
rtc[3] value = 0x00030000
DRAM DRIVE INFO: V1.50 
DRAM normal_mode value: 00000001
rsb_send_initseq: rsb clk 400Khz -> 3Mhz
PMU: AXP81X
ddr voltage = 1200 mv
ID CHECK VERSION: V0.3
using ic A83T
using axp AXP813
DRAM Type =7 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
DRAM CLK =648 MHZ
DRAM zq value: 00003bfb
dram size =2048
card boot number = 2
card no is 2
sdcard 2 line count 8
[mmc]: mmc driver ver 2015-04-13 16:05:39
[mmc]: ***Try SD card 2***
[mmc]: mmc 2 cmd 8 err 00000100
[mmc]: mmc 2 cmd 8 err 00000100
[mmc]: mmc 2 send if cond failed
[mmc]: mmc 2 cmd 55 err 00000100
[mmc]: mmc 2 cmd 55 err 00000100
[mmc]: mmc 2 send app cmd failed
[mmc]: ***Try MMC card 2***
[mmc]: mmc re-update_phase
[mmc]: mmc re-update_phase
[mmc]: 8bit ddr!!! 
[mmc]: mmc re-update_phase
[mmc]: MMC ver 4.0
[mmc]: SD/MMC Card: 8bit, capacity: 7456MB
[mmc]: vendor: Man 0090014a Snr a110d280
[mmc]: product: H8G4a
[mmc]: revision: 9.2
[mmc]: ***SD/MMC 2 init OK!!!***
sdcard 2 init ok
The size of uboot is 000e8000.
sum=322b0f36
src_sum=322b0f36
set_mmc_para,sdly 50M 0
set_mmc_para,sdly 25M 0
Succeed in loading uboot from sdmmc flash.
Ready to disable icache.
Jump to secend Boot.
[      0.290]MODE

U-Boot 2011.09-rc1-00000-gc7427fa (May 15 2019 - 20:06:30) Allwinner Technology 

[      0.299]version: 2.1.0
[      0.301]uboot commit : c7427fafe51714aab06c0c1b92b2eb684e52992d
 
normal mode
[      0.327]pmbus:   normal or secure os
ready
[      0.331]PMU: AXP81X
[      0.334]PMU: AXP81X found
bat_vol=0, ratio=100
[      0.339]PMU: dcdc2 900
[      0.342]PMU: pll1 1008 Mhz
AXI0=336 Mhz,PLL_PERIPH =1200 Mhz AHB1=200 Mhz, APB1=100 Mhz 
dcdc1_vol = 3000, onoff=1
dcdc2_vol = 900, onoff=1
dcdc3_vol = 900, onoff=1
dcdc4_vol = 900, onoff=1
dcdc6_vol = 900, onoff=1
aldo1_vol = 1800, onoff=1
aldo2_vol = 1800, onoff=1
aldo3_vol = 3000, onoff=1
eldo2_vol = 1800, onoff=0
eldo1_vol = 1200, onoff=0
dldo2_vol = 3300, onoff=0
dldo3_vol = 2800, onoff=0
dldo4_vol = 2800, onoff=0
fldo2_vol = 900, onoff=1
dldo1_vol = 3300, onoff=0
gpio0ldo_vol = 3300, onoff=0
find power_sply to end
supply=dcdc1
axp=axp81x, supply=dcdc1, vol=3000
reg addr=0x1c20b04, value=0xa, pmu_vol=3000
supply=dcdc1
axp=axp81x, supply=dcdc1, vol=3000
reg addr=0x1c20b08, value=0xa, pmu_vol=3000
supply=aldo1
axp=axp81x, supply=aldo1, vol=1800
reg addr=0x1c20b0c, value=0x0, pmu_vol=1800
supply=dcdc1
axp=axp81x, supply=dcdc1, vol=3000
reg addr=0x1c20b10, value=0xa, pmu_vol=3000
supply=dcdc1
axp=axp81x, supply=dcdc1, vol=3000
reg addr=0x1c20b14, value=0xa, pmu_vol=3000
supply=dcdc1
axp=axp81x, supply=dcdc1, vol=3000
reg addr=0x1c20b18, value=0xa, pmu_vol=3000
supply=dcdc1
axp=axp81x, supply=dcdc1, vol=3000
reg addr=0x1c20b1c, value=0xa, pmu_vol=3000
supply=aldo3
axp=axp81x, supply=aldo3, vol=3000
reg addr=0x1f02f00, value=0xa, pmu_vol=3000
config gpio bias voltage finish
vbus exist
normal dc exist, limit to dc
ac100 reg 0x00 = 0x101
ac100 reg 0xd0 = 0x0
ac100 reg 0xd1 = 0x0
fel key old mode
run key detect
no key found
no key input
dram_para_set start
dram_para_set end
[      1.068]DRAM:  2 GiB
relocation Offset is: 75ae4000
board.c 621
gic: secure os not exist
script config pll_de to 504 Mhz
Not Found clk pll_video1 in script 
Not Found clk pll_video in script 
Not Found clk pll_periph0 in script 
============tv_init==========
DRV_DISP_Init end
[      1.386]fetch script data boot_disp.output_disp fail
[      1.391]fetch script data boot_disp.output_type fail
[      1.396]fetch script data boot_disp.output_mode fail
[      1.401]fetch script data boot_disp.auto_hpd fail
[      1.406]lcd0_para.lcd_used=1
disp0 device type(1) enable
lcd_panel_fun[0].cfg_open_flow is NULL
lcd_panel_fun[0].cfg_panel_info is NULL
disp 0, clk: pll(312000000),clk(312000000),dclk(78000000) dsi_rate(78000000)
     clk real:pll(312000000),clk(0),dclk(0) dsi_rate(78000000)
lcd_panel_fun[0].cfg_open_flow is NULL
lcd_panel_fun[0].cfg_open_flow is NULL
workmode = 0
MMC:	 2
[      1.540][mmc]: mmc driver ver 2015-12-03 21:17:15
[      1.545][mmc]: get sdc_phy_wipe fail.
[      1.549][mmc]: get sdc0 sdc_erase fail.
[      1.553][mmc]: get sdc_2xmode ok, val = 1
[      1.557][mmc]: get sdc_ddrmode ok, val = 1
[      1.561][mmc]: get sdc_f_max fail,use default  50000000Hz
[      1.567][mmc]: get card_line ok, card_line = 8
[      1.571][mmc]: get sdc_ex_dly_used fail,use default
[      1.577][mmc]: SUNXI SD/MMC: 2
[      1.581][mmc]: mmc_config_clock: clk 400000
[      1.596][mmc]: *Try SD card 2*
[      1.601][mmc]: mmc 2 cmd 8 err 100
[      1.607][mmc]: mmc send if cond failed
[      1.612][mmc]: mmc 2 cmd 55 err 100
[      1.618][mmc]: send app cmd failed
[      1.621][mmc]: *Try MMC card 2*
[      1.660][mmc]: Invalid ext_csd revision 8
[      1.676][mmc]: unrecognised EXT_CSD revision 8
[      1.681][mmc]: decode ext_csd failed
[      1.684][mmc]: mmc_config_clock: clk 25000000
[      1.699][mmc]: mmc re-update_phase
[      1.706][mmc]: mmc re-update_phase
[      1.713][mmc]: mmc re-update_phase
[      1.719][mmc]: ddr8 
[      1.723][mmc]: mmc re-update_phase
[      1.730][mmc]: mmc_config_clock: clk 25000000
[      1.740][mmc]: mmc_config_clock: clk 50000000
[      1.746][mmc]: CID 0x90014a48 0x38473461 0x92a110d2 0x802726b9
[      1.751][mmc]: MMC ver 4.0
[      1.754][mmc]: mmc clk 50000000
[      1.757][mmc]: SD/MMC Card: 8bit, capacity: 7456MB
[      1.762][mmc]: boot0 capacity: 4000KB,boot1 capacity: 4000KB
[      1.768][mmc]: ***SD/MMC 2 init OK!!!***
[      1.773][mmc]: erase_grp_size:0x400WrBlk * 0x200 = 0x80000 Byte
[      1.779][mmc]: secure_feature 0x55
[      1.783][mmc]: secure_removal_type  0x3b
[      1.787]sunxi flash init ok
In:    serial
Out:   serial
Err:   serial
--------fastboot partitions--------
-total partitions:15-
-name-        -start-       -size-      
bootloader  : 1000000       2000000     
env         : 3000000       1000000     
boot        : 4000000       1000000     
system      : 5000000       80000000    
verity_block: 85000000      2000000     
misc        : 87000000      1000000     
recovery    : 88000000      2000000     
cache       : 8a000000      30000000    
metadata    : ba000000      1000000     
private     : bb000000      1000000     
frp         : bc000000      80000       
empty       : bc080000      f80000      
alog        : bd000000      5000000     
media_data  : c2000000      1000000     
UDISK       : c3000000      0           
-----------------------------------
base bootcmd=run setargs_nand boot_normal
bootcmd set setargs_mmc
key 0
recovery key high 10, low 8
cant find fstbt value
misc partition found
to be run cmd=run setargs_mmc boot_normal

** Unable to use sunxi_flash 9:0 for fatload **
load file(ULI/factory/snum.txt) error 
serial is: 100001318804b21f5425
Net:   usb_etherWarning: failed to set MAC address

mount part name bootloader
cant open script.bin, maybe it is not exist
WORK_MODE_BOOT
board_status_probe
sunxi_bmp_logo_display
[      2.049][mmc]: blkcnt should not be 0
[      2.065]fetch script data boot_disp.output_disp fail
[      2.070]screen_id =0, screen_width =800, screen_height =1280
[      2.076]frame buffer address 46400036
read item0 copy0
Item0 (Map) magic is bad
the secure storage item0 copy0 is bad
read item0 copy1
Item0 (Map) magic is bad
the secure storage item0 copy0 == copy1, the data is good
the secure storage map is empty
no item name key_burned_flag in the map
sunxi secure storage has no flag
[      2.106]usb burn from boot
delay time 0
[      2.177]usb prepare ok
[      2.979]timer occur
[      2.981]overtime
[      3.016]do_burn_from_boot usb : no usb exist
limit to dc 
[      3.022]Hit any key to stop autoboot:  0 
read boot or recovery all
[      3.201]sunxi flash read :offset 4000000, 14963648 bytes OK
[      3.211]ready to boot
[      3.213][mmc]: mmc exit start
[      3.218][mmc]: mmc_config_clock: clk 50000000
[      3.222][mmc]: mmc_config_clock: clk 400000
[      3.237][mmc]: mmc 2 cmd 8 err 100
[      3.243][mmc]: mmc send if cond failed
[      3.248][mmc]: mmc 2 cmd 55 err 100
[      3.254][mmc]: send app cmd failed
[      3.271][mmc]: get sdc_phy_wipe fail.
[      3.275][mmc]: get sdc0 sdc_erase fail.
[      3.279][mmc]: get sdc_2xmode ok, val = 1
[      3.283][mmc]: get sdc_ddrmode ok, val = 1
[      3.287][mmc]: get sdc_f_max fail,use default  50000000Hz
[      3.293][mmc]: get card_line ok, card_line = 8
[      3.297][mmc]: get sdc_ex_dly_used fail,use default
[      3.302][mmc]: mmc 2 exit ok
[      3.305]
Starting kernel ...

[sun8i_fixup]: From boot, get meminfo:
	Start:	0x40000000
	Size:	2048MB
ion_carveout reserve: 96m@0 128m@0
ion_reserve_common: ion reserve: [0xb8000000, 0xc0000000]!
ion_cma reserve: 120m@0 176m@0 512m@0
ion_reserve_common: ion reserve: [0xa0000000, 0xc0000000]!
------sun8i_smp_init_ops----37-----
[    0.000000] Booting Linux on physical CPU 0
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.4.39 (pengchj@WorldChip) (gcc version 4.6.3 20120201 (prerelease) (crosstool-NG linaro-1.13.1-2012.02-20120222 - Linaro GCC 2012.02) ) #2 SMP PREEMPT Wed May 15 20:10:54 CST 2019
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: sun8i
[    0.000000] Initialized persistent memory from 43084800-430947ff
[    0.000000] cma: CMA: reserved 512 MiB at a0000000
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] On node 0 totalpages: 524288
[    0.000000] free_area_init_node: node 0, pgdat c0948e40, node_mem_map c1402000
[    0.000000]   Normal zone: 1404 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 158340 pages, LIFO batch:31
[    0.000000]   HighMem zone: 3204 pages used for memmap
[    0.000000]   HighMem zone: 361340 pages, LIFO batch:31
[    0.000000] script_init enter!
[    0.000000] script_init exit!
[    0.000000] [mcpm_smp_init_cpus] ncores=8
[    0.000000] PERCPU: Embedded 8 pages/cpu @c2627000 s10752 r8192 d13824 u32768
[    0.000000] pcpu-alloc: s10752 r8192 d13824 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [0] 6 [0] 7 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 519680
[    0.000000] Kernel command line: boot_type=2 disp_para=100 fb_base=0x46400000 config_size=55900 androidboot.serialno=100001318804b21f5425 androidboot.hardware=sun8i console=ttyS0,115200 root=/dev/mmcblk0p7 init=/init vmalloc=384M ion_cma_list=120m,176m,512m loglevel=8 partitions=bootloader@mmcblk0p2:env@mmcblk0p5:boot@mmcblk0p6:system@mmcblk0p7:verity_block@mmcblk0p8:misc@mmcblk0p9:recovery@mmcblk0p10:cache@mmcblk0p11:metadata@mmcblk0p12:private@mmcblk0p13:frp@mmcblk0p14:empty@mmcblk0p15:alog@mmcblk0p16:media_data@mmcblk0p17:UDISK@mmcblk0p1 androidboot.selinux=enforcing
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 2048MB = 2048MB total
[    0.000000] Memory: 1537904k/1537904k available, 559248k reserved, 933888K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xe7800000 - 0xff000000   ( 376 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xe7000000   ( 624 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc08759dc   (8631 kB)
[    0.000000]       .init : 0xc0876000 - 0xc08c7a00   ( 327 kB)
[    0.000000]       .data : 0xc08c8000 - 0xc094b730   ( 526 kB)
[    0.000000]        .bss : 0xc094bd54 - 0xc0ad43d0   (1570 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:544
[    0.000000] Architected local timer running at 24.00MHz.
[    0.000000] Switching to timer-based delay loop
[    0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[    0.000000] Console: colour dummy device 80x30
[    0.000255] Calibrating delay loop (skipped), value calculated using timer frequency.. 4800.00 BogoMIPS (lpj=24000000)
[    0.000281] pid_max: default: 32768 minimum: 301
[    0.000456] Security Framework initialized
[    0.000480] SELinux:  Initializing.
[    0.000560] SELinux:  Starting in permissive mode
[    0.000647] Mount-cache hash table entries: 512
[    0.001853] Initializing cgroup subsys debug
[    0.001870] Initializing cgroup subsys freezer
[    0.001913] CPU: Testing write buffer coherency: ok
[    0.001981] ftrace: allocating 22803 entries in 67 pages
[    0.030300] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.030352] Setting up static identity map for 0x405ebe68 - 0x405ebec0
[    0.031405] CPU1: Booted secondary processor
[    0.031405] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.031513] CPU2: Booted secondary processor
[    0.031513] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.031513] CPU3: Booted secondary processor
[    0.031513] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.040534] CPU4: failed to boot: -22
[    0.040643] CPU5: failed to boot: -22
[    0.040643] CPU6: failed to boot: -22
[    0.040643] CPU7: failed to boot: -22
[    0.040643] Brought up 4 CPUs
[    0.040643] SMP: Total of 4 processors activated (19200.00 BogoMIPS).
[    0.040729] devtmpfs: initialized
[    0.053329] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.053845] pinctrl core: initialized pinctrl subsystem
[    0.074382] NET: Registered protocol family 16
[    0.075551] DMA: preallocated 2048 KiB pool for atomic coherent allocations
[    0.075551] script_sysfs_init success
[    0.075551] sunxi_dump_init success
[    0.075551] gpiochip_add: registered GPIOs 0 to 383 on device: sunxi-pinctrl
[    0.076591] sunxi-pinctrl sunxi-pinctrl: initialized sunXi PIO driver
[    0.077003] gpiochip_add: registered GPIOs 1024 to 1031 on device: axp-pinctrl
[    0.078274] persistent_ram: uncorrectable error in header
[    0.078288] persistent_ram: no valid data in buffer (sig = 0xffffffff)
[    0.089411] console [ram-1] enabled
[    0.089813] [sunxi-module]: [sunxi-module.0] probe success
[    0.090390] Not Found clk pll_video1 in script 
[    0.090502] script config pll_ve to 432 Mhz
[    0.090684] Not Found clk pll_periph in script 
[    0.090788] script config pll_gpu to 432 Mhz
[    0.090893] script config pll_hsic to 480 Mhz
[    0.091079] script config pll_de to 504 Mhz
[    0.091177] sunxi_default_clk_init
[    0.091277] try to set pll6ahb1 to 200000000
[    0.091492] try to set ahb clk source to pll6ahb1
[    0.091593] set ahb clk source to pll6ahb1
[    0.091774] try to set ahb1 to 200000000
[    0.091875] try to set apb1 to 100000000
[    0.092976] ===fe3o4==== sunxi_root_procfs_attach ret:0
[    0.100473] bio: create slab <bio-0> at 0
[    0.100618] [ARISC] :sunxi-arisc driver v1.03
[    0.109946] [ARISC] :arisc version: [v0.1.79]
[    0.110438] sunxi_get_soc_bin: slow chip
[    0.111010] [ARISC] :sunxi-arisc driver v1.03 startup succeeded
[    0.120187] CPU4: Booted secondary processor
[    0.120187] CPU4: thread -1, cpu 0, socket 1, mpidr 80000100
[    0.123496] CPU5: Booted secondary processor
[    0.123496] CPU5: thread -1, cpu 1, socket 1, mpidr 80000101
[    0.130307] CPU6: Booted secondary processor
[    0.130307] CPU6: thread -1, cpu 2, socket 1, mpidr 80000102
[    0.130307] CPU7: Booted secondary processor
[    0.130307] CPU7: thread -1, cpu 3, socket 1, mpidr 80000103
[    0.140349] pwm module init!
[    0.141550] SCSI subsystem initialized
[    0.141550] usbcore: registered new interface driver usbfs
[    0.141550] usbcore: registered new interface driver hub
[    0.141550] usbcore: registered new device driver usb
[    0.141550] twi_chan_cfg()340 - [twi0] has no twi_regulator.
[    0.141550] twi_chan_cfg()340 - [twi1] has no twi_regulator.
[    0.141550] twi_chan_cfg()340 - [twi2] has no twi_regulator.
[    0.141550] twi_chan_cfg()332 - [twi3] has no twi_used!
[    0.141550] twi_chan_cfg()352 - [twi3] has no twi_used!
[    0.141731] Linux video capture interface: v2.00
[    0.190401] Advanced Linux Sound Architecture Driver Version 1.0.25.
[    0.191256] Bluetooth: Core ver 2.16
[    0.191398] NET: Registered protocol family 31
[    0.191501] Bluetooth: HCI device and connection manager initialized
[    0.191686] Bluetooth: HCI socket layer initialized
[    0.191787] Bluetooth: L2CAP socket layer initialized
[    0.191989] Bluetooth: SCO socket layer initialized
[    0.200283] cfg80211: Calling CRDA to update world regulatory domain
[    0.200701] Switching to clocksource arch_sys_counter
[    0.219369] FS-Cache: Loaded
[    0.219829] CacheFiles: Loaded
[    0.232059] axp81x_dcdc1: Failed to create debugfs directory
[    0.233871] NET: Registered protocol family 2
[    0.234277] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.235385] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.238021] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[    0.239670] TCP: Hash tables configured (established 131072 bind 65536)
[    0.239853] TCP: reno registered
[    0.239957] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.240231] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.240765] NET: Registered protocol family 1
[    0.241238] Unpacking initramfs...
[    0.540627] Freeing initrd memory: 4100K
[    0.543006] [pm]aw_pm_init!
[    0.543194] standby_mode = 0. 
[    0.543293] aw_pm_init: not support super standby. 
[    0.543394] wakeup src cnt is : 3. 
[    0.543580] pmu name: pmu1_para .
[    0.543684] pmu1_enable = 0x1. 
[    0.543783] pmux_id = 0x7. 
[    0.543885] pmu name: pmu2_para .
[    0.544065] config_pmux_para: script_parser_fetch err. 
[    0.544166] pmu2_enable = 0x0. 
[    0.544678] add_sys_pwr_dm: axp81x_aldo2 ldo already alwayson.
[    0.545015] add_sys_pwr_dm: axp81x_aldo2 ldo already alwayson.
[    0.545127] add_sys_pwr_dm: axp81x_aldo2 ldo already alwayson.
[    0.545309] after inited: sys_mask config = 0x6bd5. 
[    0.545411] dynamic_standby enalbe = 0x0. 
[    0.545650] sunxi_reg_init enter
[    0.546188] lock super standby for a83!
[    0.546296] lookup_scene_lock_name: new scene lock super_standby
[    0.546475] scene_lock_init name=super_standby
[    0.546577] scene_lock: super_standby, type 5, count 1
[    0.547360] audit: initializing netlink socket (disabled)
[    0.547512] type=2000 audit(0.540:1): initialized
[    0.548577] highmem bounce pool size: 64 pages
[    0.550354] NTFS driver 2.1.30 [Flags: R/W].
[    0.550663] fuse init (API version 7.18)
[    0.551415] msgmni has been set to 1187
[    0.551553] SELinux:  Registering netfilter hooks
[    0.554220] io scheduler noop registered
[    0.554405] io scheduler deadline registered
[    0.554622] io scheduler cfq registered (default)
[    0.556320] uart0: ttyS0 at MMIO 0x1c28000 (irq = 32) is a SUNXI
[    0.556429] sw_uart_pm()890 - uart0 clk is already enable
[    0.556621] sw_console_setup()1233 - console setup baud 115200 parity n bits 8, flow n
[    0.653350] console [ttyS0] enabled
[    0.752639] axp81x_dcdc1: Failed to create debugfs directory
[    0.851503] uart1: ttyS1 at MMIO 0x1c28400 (irq = 33) is a SUNXI
[    0.950394] axp81x_dcdc1: Failed to create debugfs directory
[    1.146771] uart2: ttyS2 at MMIO 0x1c28800 (irq = 34) is a SUNXI
[    1.245475] axp81x_dcdc1: Failed to create debugfs directory
[    1.343928] uart4: ttyS4 at MMIO 0x1c29000 (irq = 36) is a SUNXI
[    1.448264] loop: module loaded
[    1.680248] [rf_pm]: select module num is 9
[    1.685101] [rf_pm]: module power1 name vcc-wifi-io
[    1.690674] [rf_pm]: module power1 vol 3300000
[    1.695736] [rf_pm]: module power2 name 
[    1.700312] [rf_pm]: failed to fetch module_power2_vol
[    1.706152] [rf_pm]: module power3 name 
[    1.710726] [rf_pm]: failed to fetch module_power3_vol
[    1.716565] [rf_pm]: mod has no power_switch gpio
[    1.721935] [rf_pm]: mod has no chip_en gpio
[    1.726882] [rf_pm]: lpo_use_apclk: ac10032k2
[    1.731937] [rf_pm]: get power regulator  failed.
[    1.737371] [rf_pm]: set vcc-wifi-io to 3300000 v
[    1.742817] [rf_pm]: enable vcc-wifi-io.
[    1.747857] [rf_pm]: mod info power switch -1
[    1.753010] [rf_pm]: set ac10032k2 32k out
[    1.757790] scene_lock_init name=rf_pm
[    1.762383] [wifi_pm]: wifi gpio init is OK !!
[    1.767587] [rfkill]: mod has no ls_int gpio
[    1.772483] [rfkill]: mod has no pcm_ch gpio
[    1.778364] axp81x_dcdc1: Failed to create debugfs directory
[    1.785073] spi spi0: master is unqueued, this is deprecated
[    1.791722] tun: Universal TUN/TAP device driver, 1.6
[    1.797462] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    1.804806] PPP generic driver version 2.4.2
[    1.809854] PPP BSD Compression module registered
[    1.815228] PPP Deflate Compression module registered
[    1.822319] PPP MPPE Compression module registered
[    1.827775] NET: Registered protocol family 24
[    1.832946] PPTP driver version 0.8.5
[    1.837734] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.865248] sunxi-ehci sunxi-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.874414] sunxi-ehci sunxi-ehci.1: new USB bus registered, assigned bus number 1
[    1.884954] sunxi-ehci sunxi-ehci.1: irq 104, io mem 0xf1c1a000
[    1.910040] sunxi-ehci sunxi-ehci.1: USB 0.0 started, EHCI 1.00
[    1.916845] ehci_irq: highspeed device connect
[    1.922032] hub 1-0:1.0: USB hub found
[    1.926408] hub 1-0:1.0: 1 port detected
[    1.931367] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.958557] sunxi-ohci sunxi-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver
[    1.967249] sunxi-ohci sunxi-ohci.1: new USB bus registered, assigned bus number 2
[    1.975960] sunxi-ohci sunxi-ohci.1: irq 105, io mem 0xf1c1a400
[    2.044680] hub 2-0:1.0: USB hub found
[    2.049055] hub 2-0:1.0: 1 port detected
[    2.054129] usbcore: registered new interface driver cdc_acm
[    2.060655] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    2.069697] Initializing USB Mass Storage driver...
[    2.075436] usbcore: registered new interface driver usb-storage
[    2.082243] USB Mass Storage support registered.
[    2.087621] usbcore: registered new interface driver ums-alauda
[    2.094394] usbcore: registered new interface driver ums-cypress
[    2.101350] usbcore: registered new interface driver ums-datafab
[    2.108210] usbcore: registered new interface driver ums_eneub6250
[    2.115358] usbcore: registered new interface driver ums-freecom
[    2.122209] usbcore: registered new interface driver ums-isd200
[    2.129043] usbcore: registered new interface driver ums-jumpshot
[    2.136041] usbcore: registered new interface driver ums-karma
[    2.142807] usbcore: registered new interface driver ums-onetouch
[    2.149772] usbcore: registered new interface driver ums-realtek
[    2.156765] usbcore: registered new interface driver ums-sddr09
[    2.163523] usbcore: registered new interface driver ums-sddr55
[    2.170360] usbcore: registered new interface driver ums-usbat
[    2.177188] usbcore: registered new interface driver usbserial
[    2.183830] usbserial: USB Serial Driver core
[    2.188853] usbcore: registered new interface driver option
[    2.195284] USB Serial support registered for GSM modem (1-port)
[    2.250065] usb 1-1: new high-speed USB device number 2 using sunxi-ehci
[    2.402636] hub 1-1:1.0: USB hub found
[    2.407239] hub 1-1:1.0: 4 ports detected
[    2.414801] file system registered
[    2.420643] android_usb gadget: Mass Storage Function, version: 2009/09/11
[    2.428512] android_usb gadget: Number of LUNs=3
[    2.433787]  lun0: LUN: removable file: (no medium)
[    2.439335]  lun1: LUN: removable file: (no medium)
[    2.444983]  lun2: LUN: removable file: (no medium)
[    2.450939] get usb_serial_number success from boot command line
[    2.457648] android_usb gadget: android_usb ready
[    2.463787] axp81x_dcdc1: Failed to create debugfs directory
[    2.470350] sunxi_hcd_host0 sunxi_hcd_host0: sunxi_hcd host driver
[    2.477364] sunxi_hcd_host0 sunxi_hcd_host0: new USB bus registered, assigned bus number 3
[    2.487515] hub 3-0:1.0: USB hub found
[    2.491837] hub 3-0:1.0: 1 port detected
[    2.497411] mousedev: PS/2 mouse device common for all mice
[    2.504046] sunxikbd_script_init: key para not found, used default para. 
[    2.512507] sunxi_rtc_init(836): sunxi rtc device register!
[    2.519710] rtc_gettime(340): read time 1970-1-1 1:0:7
[    2.525988] alarm_gettime(477): get alarm time 1970-1-1 1:0:0 success!
[    2.533852] rtc_gettime(340): read time 1970-1-1 1:0:7
[    2.540045] rtc0 rtc0: rtc core: registered rtc0 as rtc0
[    2.546285] sunxi_rtc_probe(775)!
[    2.550233] i2c /dev entries driver
[    2.554904] IR RC5(x) protocol handler initialized
[    2.560500] sunxi cedar version 0.1 
[    2.564732] [cedar]: install start!!!
[    2.569156] [cedar]: install end!!!
[    2.579279] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[    2.589225] Bluetooth: HCI UART driver ver 2.2
[    2.594374] Bluetooth: HCI H4 protocol initialized
[    2.599901] Bluetooth: HCI Realtek H5 protocol initialized
[    2.606627] sunxi_get_soc_bin: slow chip
[    2.613877] [mmc]: SD/MMC/SDIO Host Controller Driver(v1.116 2015-7-11 11:55) Compiled in May 15 2019 at 20:10:11
[    2.625361] [mmc]: get mmc2's 2xmode ok, val = 1
[    2.630550] [mmc]: get mmc2's ddrmode ok, val = 1
[    2.635828] [mmc]: MMC host used card: 0x4, boot card: 0x4, io_card 0
[    2.643969] [mmc]: sdc2 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.654927] [mmc]: sdc2 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.656647] usbcore: registered new interface driver usbhid
[    2.656652] usbhid: USB HID core driver
[    2.656658] zram: num_devices not specified. Using default: 1
[    2.656663] zram: Creating 1 devices ...
[    2.686721] ashmem: initialized
[    2.690418] logger: created 256K log 'log_main'
[    2.695676] logger: created 256K log 'log_events'
[    2.700031] [mmc]: sdc2 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.711304] logger: created 256K log 'log_radio'
[    2.716579] logger: created 256K log 'log_system'
[    2.720835] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 52,  RTO !!
[    2.721664] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 52,  RTO !!
[    2.721683] [mmc]: sdc2 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.724144] [mmc]: sdc2 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.726033] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 8,  RTO !!
[    2.726050] *******************Try sdio*******************
[    2.726863] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 5,  RTO !!
[    2.727686] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 5,  RTO !!
[    2.728508] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 5,  RTO !!
[    2.729331] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 5,  RTO !!
[    2.729347] *******************Try sd *******************
[    2.730161] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 55,  RTO !!
[    2.730988] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 55,  RTO !!
[    2.731816] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 55,  RTO !!
[    2.732641] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 55,  RTO !!
[    2.732662] *******************Try mmc*******************
[    2.732670] [mmc]: sdc2 set ios: clk 400000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.733074] [mmc]: sdc2 set ios: clk 400000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.733157] [mmc]: sdc2 set ios: clk 400000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.733239] [mmc]: sdc2 set ios: clk 400000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.735697] [mmc]: sdc2 set ios: clk 400000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.771212] [mmc]: sdc2 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.783205] mmc0: unrecognised EXT_CSD revision 8
[    2.783217] mmc0: error -22 whilst initialising MMC card
[    2.783224] [mmc]: sdc2 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.785937] [mmc]: sdc2 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.800030] [mmc]: sdc2 set ios: clk 300000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.821102] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 52,  RTO !!
[    2.822195] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 52,  RTO !!
[    2.822214] [mmc]: sdc2 set ios: clk 300000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.824802] [mmc]: sdc2 set ios: clk 300000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.826973] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 8,  RTO !!
[    2.826990] *******************Try sdio*******************
[    2.828073] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 5,  RTO !!
[    2.829167] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 5,  RTO !!
[    2.830260] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 5,  RTO !!
[    2.831353] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 5,  RTO !!
[    2.831370] *******************Try sd *******************
[    2.832450] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 55,  RTO !!
[    2.833543] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 55,  RTO !!
[    2.834637] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 55,  RTO !!
[    2.835730] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 55,  RTO !!
[    2.835746] *******************Try mmc*******************
[    2.835754] [mmc]: sdc2 set ios: clk 300000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.836264] [mmc]: sdc2 set ios: clk 300000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.836359] [mmc]: sdc2 set ios: clk 300000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.836453] [mmc]: sdc2 set ios: clk 300000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.839042] [mmc]: sdc2 set ios: clk 300000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.846036] gpio_switch_init(749): sunxi switch driver register!
[    2.901581] [mmc]: sdc2 set ios: clk 300000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.917348] mmc0: unrecognised EXT_CSD revision 8
[    2.917355] mmc0: error -22 whilst initialising MMC card
[    2.917362] [mmc]: sdc2 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.920068] [mmc]: sdc2 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.940022] [mmc]: sdc2 set ios: clk 200000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.944072] i2c-core: driver [ts3a225] using legacy suspend method
[    2.961639] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 52,  RTO !!
[    2.963268] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 52,  RTO !!
[    2.963287] [mmc]: sdc2 set ios: clk 200000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.966141] [mmc]: sdc2 set ios: clk 200000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.968875] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 8,  RTO !!
[    2.968891] *******************Try sdio*******************
[    2.970510] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 5,  RTO !!
[    2.972140] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 5,  RTO !!
[    2.973770] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 5,  RTO !!
[    2.975400] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 5,  RTO !!
[    2.975416] *******************Try sd *******************
[    2.977035] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 55,  RTO !!
[    2.978665] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 55,  RTO !!
[    2.980295] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 55,  RTO !!
[    2.981925] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 55,  RTO !!
[    2.981941] *******************Try mmc*******************
[    2.981948] [mmc]: sdc2 set ios: clk 200000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.982682] [mmc]: sdc2 set ios: clk 200000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.982803] [mmc]: sdc2 set ios: clk 200000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.982919] [mmc]: sdc2 set ios: clk 200000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.985774] [mmc]: sdc2 set ios: clk 200000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    3.022333] [mmc]: sdc2 set ios: clk 200000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    3.041896] i2c-core: driver [ts3a225] using legacy resume method
[    3.045669] mmc0: unrecognised EXT_CSD revision 8
[    3.045676] mmc0: error -22 whilst initialising MMC card
[    3.045682] [mmc]: sdc2 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    3.048374] [mmc]: sdc2 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    3.070024] [mmc]: sdc2 set ios: clk 150000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    3.092179] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 52,  RTO !!
[    3.094339] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 52,  RTO !!
[    3.094357] [mmc]: sdc2 set ios: clk 150000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    3.097476] [mmc]: sdc2 set ios: clk 150000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    3.100773] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 8,  RTO !!
[    3.100791] *******************Try sdio*******************
[    3.102947] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 5,  RTO !!
[    3.105107] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 5,  RTO !!
[    3.107267] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 5,  RTO !!
[    3.109427] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 5,  RTO !!
[    3.109443] *******************Try sd *******************
[    3.111600] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 55,  RTO !!
[    3.113760] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 55,  RTO !!
[    3.115920] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 55,  RTO !!
[    3.118080] [mmc]: *** sunxi_mci_dump_errinfo(L824): smc 2 err, cmd 55,  RTO !!
[    3.118097] *******************Try mmc*******************
[    3.118104] [mmc]: sdc2 set ios: clk 150000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    3.119065] [mmc]: sdc2 set ios: clk 150000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    3.119209] [mmc]: sdc2 set ios: clk 150000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    3.119350] [mmc]: sdc2 set ios: clk 150000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    3.122466] [mmc]: sdc2 set ios: clk 150000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    3.163072] [mmc]: sdc2 set ios: clk 150000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    3.193967] mmc0: unrecognised EXT_CSD revision 8
[    3.193973] mmc0: error -22 whilst initialising MMC card
[    3.193980] [mmc]: sdc2 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    3.238945] sunxi_i2c_do_xfer()985 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x3b)
[    3.659082] i2c_read_interface error1
[    3.663254] sunxi_i2c_do_xfer()985 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x3b)
[    3.672565] i2c_read_interface error1
[    3.672582] gpio_switch_probe,line:539,val:0
[    3.672932] sunxi_oops: heming add OOPS_INFO_ADDR = -20
[    3.673253] usbcore: registered new interface driver snd-usb-audio
[    3.694588] sunxi_i2c_do_xfer()985 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x3b)
[    3.703903] i2c_write_interface error
[    3.720366] asoc: ac100-aif1 <-> pri_dai mapping ok
[    3.726128] asoc: ac100-aif2 <-> bb-voice-dai mapping ok
[    3.736025] asoc: ac100-aif1 <-> sec_dai mapping ok
[    3.741805] asoc: ac100-aif3 <-> bb-voice-dai mapping ok
[    3.747970] asoc: ac100-aif2 <-> bb-voice-dai mapping ok
[    3.761465] asoc: sndhdmi <-> sunxi-hdmiaudio.0 mapping ok
[    3.768517] u32 classifier
[    3.771659]     Actions configured
[    3.775495] Netfilter messages via NETLINK v0.30.
[    3.780865] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[    3.788211] ctnetlink v0.93: registering with nfnetlink.
[    3.794245] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[    3.802106] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[    3.809022] xt_time: kernel timezone is -0000
[    3.814056] sunxi_i2c_do_xfer()985 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x3b)
[    3.814128] IPv4 over IPv4 tunneling driver
[    3.814530] gre: GRE over IPv4 demultiplexor driver
[    3.814536] ip_gre: GRE over IPv4 tunneling driver
[    3.815132] ip_tables: (C) 2000-2006 Netfilter Core Team
[    3.815328] arp_tables: (C) 2002 David S. Miller
[    3.815389] TCP: cubic registered
[    3.815393] Initializing XFRM netlink socket
[    3.858655] i2c_read_interface error1
[    3.862851] [switch] ti3s225 initial the wrong state,238.
[    3.869048] NET: Registered protocol family 10
[    3.874082] sunxi_i2c_do_xfer()985 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x3b)
[    3.883418] i2c_write_interface error
[    3.888078] Mobile IPv6
[    3.890895] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    3.897122] IPv6 over IPv4 tunneling driver
[    3.902755] NET: Registered protocol family 17
[    3.907764] NET: Registered protocol family 15
[    3.912971] Bluetooth: RFCOMM TTY layer initialized
[    3.918506] Bluetooth: RFCOMM socket layer initialized
[    3.924313] Bluetooth: RFCOMM ver 1.11
[    3.928597] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    3.934578] Bluetooth: BNEP filters: protocol multicast
[    3.940443] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    3.947554] ThumbEE CPU extension supported.
[    3.952396] Registering SWP/SWPB emulation handler
[    3.959537] rtc_gettime(340): read time 1970-1-1 1:0:8
[    3.965359] rtc0 rtc0: setting system clock to 1970-01-01 01:00:08 UTC (3608)
[    3.974309] sunxi_get_soc_bin: slow chip
[    3.979194] CPU Budget:Register notifier
[    3.983733] CPU Budget:register Success
[    3.988051] sunxi-budget-cooling sunxi-budget-cooling: Cooling device registered: thermal-budget-0
[    4.002349] =========GPS========= :gsp not used in configuration
[    4.009075] ALSA device list:
[    4.012458]   #0: sndac100
[    4.015580]   #1: sndhdmi
[    4.019192] Freeing init memory: 324K
[    4.025712] init: init started!
[    4.033712] SELinux: 2048 avtab hash slots, 5054 rules.
[    4.039692] SELinux:  Android master kernel running Android M policy in compatibility mode.
[    4.051236] SELinux: 2048 avtab hash slots, 5054 rules.
[    4.057144] SELinux:  1 users, 2 roles, 540 types, 0 bools, 1 sens, 1024 cats
[    4.065366] SELinux:  87 classes, 5054 rules
[    4.072126] SELinux:  Completing initialization.
[    4.077391] SELinux:  Setting up existing superblocks.
[    4.083228] SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
[    4.091339] SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
[    4.099627] SELinux: initialized (dev bdev, type bdev), not configured for labeling
[    4.108325] SELinux: initialized (dev proc, type proc), uses genfs_contexts
[    4.116220] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[    4.124359] SELinux: initialized (dev devtmpfs, type devtmpfs), uses transition SIDs
[    4.133631] SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
[    4.155613] SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
[    4.163418] SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
[    4.171235] SELinux: initialized (dev anon_inodefs, type anon_inodefs), not configured for labeling
[    4.181466] SELinux: initialized (dev devpts, type devpts), uses transition SIDs
[    4.189807] SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
[    4.198740] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[    4.206932] SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
[    4.210051] switch_status_update,line:179,switch_data->state:0
[    4.390034] switch_status_update,line:179,switch_data->state:0
[    4.417050] type=1403 audit(3608.940:2): policy loaded auid=4294967295 ses=4294967295
[    4.426434] type=1404 audit(3608.960:3): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
[    4.650232] init: (Initializing SELinux enforcing took 0.62s.)
[    4.663640] init: init second stage started!
[    4.709919] init: waitpid failed: No child processes
[    4.715925] init: (Loading properties from /default.prop took 0.00s.)
[    4.725312] init: (Parsing /init.environ.rc took 0.00s.)
[    4.731582] init: (Parsing /init.usb.rc took 0.00s.)
[    4.737966] init: (Parsing init.sensors.rc took 0.00s.)
[    4.743924] init: (Parsing init.common.rc took 0.01s.)
[    4.749849] init: (Parsing init.sun8i.common.rc took 0.00s.)
[    4.756435] init: (Parsing init.sun8i.usb.rc took 0.00s.)
[    4.762574] init: (Parsing /init.sun8i.rc took 0.03s.)
[    4.768727] init: (Parsing /init.usb.configfs.rc took 0.00s.)
[    4.775288] init: (Parsing /init.zygote32.rc took 0.00s.)
[    4.781544] init: (Parsing /init.trace.rc took 0.00s.)
[    4.787329] init: (Parsing /init.rc took 0.06s.)
[    4.792772] init: SELinux: Could not get canonical path /adb_keys restorecon: No such file or directory.
[    4.803510] init: Starting service 'ueventd'...
[    4.809294] init: Waiting for /dev/.coldboot_done...
[    4.811911] ueventd: ueventd started!
[    5.384952] ueventd: Coldboot took 0.57s.
[    5.393428] init: Waiting for /dev/.coldboot_done took 0.58s.
[    5.399984] init: /dev/hw_random not found
[    5.405846] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[    5.415432] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[    5.426478] init: write_file: Unable to open '/proc/sys/kernel/hung_task_timeout_secs': No such file or directory
[    5.438165] init: write_file: Unable to open '/proc/sys/kernel/sched_tunable_scaling': No such file or directory
[    5.449653] init: write_file: Unable to open '/proc/sys/kernel/sched_latency_ns': No such file or directory
[    5.460674] init: write_file: Unable to open '/proc/sys/kernel/sched_wakeup_granularity_ns': No such file or directory
[    5.472735] init: write_file: Unable to open '/proc/sys/kernel/sched_compat_yield': No such file or directory
[    5.590183] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
[    5.598602] init: write_file: Unable to write to '/dev/cpuctl/cpu.shares': Invalid argument
[    5.610666] init: write_file: Unable to open '/proc/sys/abi/swp': No such file or directory
[    5.620906] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[    5.629340] init: /dev/hw_random not found
[    5.659757] [NAND]nand init start, nand0_used_flag is 0
[    5.665720] [NAND]nand driver is disabled 
[   25.001496] fs_mgr: __mount(source=/dev/block/by-name/system,target=/system,type=ext4)=-1
[   25.010824] fs_mgr: Failed to mount an un-encryptable or wiped partition on/dev/block/by-name/system at /system options: barrier=1 error: No such file or directory
[   45.001140] fs_mgr: check_fs(): mount(/dev/block/by-name/cache,/cache,ext4)=-1: No such file or directory
[   45.011972] fs_mgr: Not running /system/bin/e2fsck on /dev/block/by-name/cache (executable not in system image)
[   45.023444] fs_mgr: __mount(source=/dev/block/by-name/cache,target=/cache,type=ext4)=-1
[   45.032470] fs_mgr: Failed to mount an un-encryptable or wiped partition on/dev/block/by-name/cache at /cache options: barrier=1,data=ordered,nomblk_io_submit,noauto_da_alloc,errors=panic error: No such file or directory
[   65.008100] fs_mgr: check_fs(): mount(/dev/block/by-name/alog,/logger,ext4)=-1: No such file or directory
[   65.018939] fs_mgr: Not running /system/bin/e2fsck on /dev/block/by-name/alog (executable not in system image)
[   65.030295] fs_mgr: __mount(source=/dev/block/by-name/alog,target=/logger,type=ext4)=-1
[   65.039311] fs_mgr: Failed to mount an un-encryptable or wiped partition on/dev/block/by-name/alog at /logger options: barrier=1,data=ordered,nomblk_io_submit,noauto_da_alloc,errors=panic error: No such file or directory
[   85.004897] fs_mgr: check_fs(): mount(/dev/block/by-name/UDISK,/data,ext4)=-1: No such file or directory
[   85.015631] fs_mgr: Not running /system/bin/e2fsck on /dev/block/by-name/UDISK (executable not in system image)
[   85.027088] fs_mgr: __mount(source=/dev/block/by-name/UDISK,target=/data,type=ext4)=-1
[   85.036077] fs_mgr: fs_mgr_mount_all(): possibly an encryptable blkdev /dev/block/by-name/UDISK for mount /data type ext4 )
[   85.048770] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[   85.056962] init: fs_mgr_mount_all returned an error
[   85.062980] init: fs_mgr_mount_all returned unexpected error 255
[   85.072680] Unable to find swap-space signature
[   85.077924] fs_mgr: swapon failed for /dev/block/zram0
[   90.090902] init: can't not open file!
[   91.095245] init: can't not open file!
[   92.099626] init: can't not open file!
[   93.104035] init: can't not open file!
[   94.108358] init: can't not open file!

[END] 2019/5/16 9:55:50

上面的不正常的?再贴一份正常的上来吧, 用 code 标签.

离线

#5 2019-05-16 19:20:24

MrJacky
会员
注册时间: 2019-02-26
累计积分: 8

Re: 全志A83T无法进系统问题

þHELLO! BOOT0 is starting!
boot0 version : 4.2.0
boot0 commit : ba81bb80fe217e401fc0bee185e0a53ba1a17e7d
 
rtc[1] value = 0x00010000
rtc[2] value = 0x00020000
rtc[3] value = 0x00030000
DRAM DRIVE INFO: V1.50 
DRAM normal_mode value: 00000001
rsb_send_initseq: rsb clk 400Khz -> 3Mhz
PMU: AXP81X
ddr voltage = 1200 mv
ID CHECK VERSION: V0.3
using ic A83T
using axp AXP813
DRAM Type =7 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
DRAM CLK =648 MHZ
DRAM zq value: 00003bfb
dram size =2048
card boot number = 2
card no is 2
sdcard 2 line count 8
[mmc]: mmc driver ver 2015-04-13 16:05:39
[mmc]: ***Try SD card 2***
[mmc]: mmc 2 cmd 8 err 00000100
[mmc]: mmc 2 cmd 8 err 00000100
[mmc]: mmc 2 send if cond failed
[mmc]: mmc 2 cmd 55 err 00000100
[mmc]: mmc 2 cmd 55 err 00000100
[mmc]: mmc 2 send app cmd failed
[mmc]: ***Try MMC card 2***
[mmc]: mmc re-update_phase
[mmc]: mmc re-update_phase
[mmc]: 8bit ddr!!! 
[mmc]: mmc re-update_phase
[mmc]: MMC ver 4.0
[mmc]: SD/MMC Card: 8bit, capacity: 7456MB
[mmc]: vendor: Man 0090014a Snr a110d280
[mmc]: product: H8G4a
[mmc]: revision: 9.2
[mmc]: ***SD/MMC 2 init OK!!!***
sdcard 2 init ok
The size of uboot is 000ec000.
sum=77d64102
src_sum=77d64102
set_mmc_para,sdly 50M 0
set_mmc_para,sdly 25M 0
Succeed in loading uboot from sdmmc flash.
Ready to disable icache.
Jump to secend Boot.
[      0.291]MODE

U-Boot 2011.09-rc1-00000-gba81bb8-dirty (Mar 21 2019 - 17:36:40) Allwinner Technology 

[      0.300]version: 2.1.0
[      0.303]uboot commit : ba81bb80fe217e401fc0bee185e0a53ba1a17e7d
 
normal mode
[      0.329]pmbus:   normal or secure os
ready
[      0.333]PMU: AXP81X
[      0.336]PMU: AXP81X found
bat_vol=0, ratio=100
[      0.341]PMU: dcdc2 900
[      0.343]PMU: pll1 1008 Mhz
AXI0=336 Mhz,PLL_PERIPH =1200 Mhz AHB1=200 Mhz, APB1=100 Mhz 
dcdc1_vol = 3000, onoff=1
dcdc2_vol = 900, onoff=1
dcdc3_vol = 900, onoff=1
dcdc4_vol = 900, onoff=1
dcdc6_vol = 900, onoff=1
aldo1_vol = 1800, onoff=1
aldo2_vol = 1800, onoff=1
aldo3_vol = 3000, onoff=1
eldo2_vol = 1800, onoff=0
eldo1_vol = 1200, onoff=0
dldo2_vol = 3300, onoff=0
dldo3_vol = 2800, onoff=0
dldo4_vol = 2800, onoff=0
fldo2_vol = 900, onoff=1
dldo1_vol = 3300, onoff=0
gpio0ldo_vol = 3300, onoff=0
find power_sply to end
supply=dcdc1
axp=axp81x, supply=dcdc1, vol=3000
reg addr=0x1c20b04, value=0xa, pmu_vol=3000
supply=dcdc1
axp=axp81x, supply=dcdc1, vol=3000
reg addr=0x1c20b08, value=0xa, pmu_vol=3000
supply=aldo1
axp=axp81x, supply=aldo1, vol=1800
reg addr=0x1c20b0c, value=0x0, pmu_vol=1800
supply=dcdc1
axp=axp81x, supply=dcdc1, vol=3000
reg addr=0x1c20b10, value=0xa, pmu_vol=3000
supply=dcdc1
axp=axp81x, supply=dcdc1, vol=3000
reg addr=0x1c20b14, value=0xa, pmu_vol=3000
supply=dcdc1
axp=axp81x, supply=dcdc1, vol=3000
reg addr=0x1c20b18, value=0xa, pmu_vol=3000
supply=dcdc1
axp=axp81x, supply=dcdc1, vol=3000
reg addr=0x1c20b1c, value=0xa, pmu_vol=3000
supply=aldo3
axp=axp81x, supply=aldo3, vol=3000
reg addr=0x1f02f00, value=0xa, pmu_vol=3000
config gpio bias voltage finish
vbus exist
normal dc exist, limit to dc
ac100 reg 0x00 = 0x101
ac100 reg 0xd0 = 0x0
ac100 reg 0xd1 = 0x0
fel key old mode
run key detect
no key found
no key input
dram_para_set start
dram_para_set end
[      1.070]DRAM:  2 GiB
relocation Offset is: 75adf000
board.c 621
gic: secure os not exist
script config pll_de to 504 Mhz
Not Found clk pll_video1 in script 
Not Found clk pll_video in script 
Not Found clk pll_periph0 in script 
============tv_init==========
DRV_DISP_Init end
[      1.389]fetch script data boot_disp.output_disp fail
[      1.394]fetch script data boot_disp.output_type fail
[      1.399]fetch script data boot_disp.output_mode fail
[      1.404]fetch script data boot_disp.auto_hpd fail
[      1.409]lcd0_para.lcd_used=1
disp0 device type(1) enable
disp 0, clk: pll(312000000),clk(312000000),dclk(78000000) dsi_rate(78000000)
     clk real:pll(312000000),clk(0),dclk(0) dsi_rate(78000000)
enable power vcc-mipi, ret=0
enable power vcc-dsi, ret=0
enable power vcc-pd, ret=0
workmode = 0
MMC:	 2
[      1.575][mmc]: mmc driver ver 2016-03-24 19:30:15
[      1.580][mmc]: get sdc_phy_wipe fail.
[      1.584][mmc]: get sdc0 sdc_erase fail.
[      1.588][mmc]: get sdc_2xmode ok, val = 1
[      1.592][mlcd model name D9366
use old lcd!!!
mc]: get sdc_ddrmode ok, val = 1
[      1.737][mmc]: get sdc_f_max fail,use default  50000000Hz
[      1.743][mmc]: get card_line ok, card_line = 8
[      1.747][mmc]: get sdc_ex_dly_used fail,use default
[      1.752][mmc]: SUNXI SD/MMC: 2
[      1.757][mmc]: mmc_config_clock: clk 400000
[      1.772][mmc]: *Try SD card 2*
[      1.777][mmc]: mmc 2 cmd 8 err 100
[      1.783][mmc]: mmc send if cond failed
[      1.788][mmc]: mmc 2 cmd 55 err 100
[      1.794][mmc]: send app cmd failed
[      1.797][mmc]: *Try MMC card 2*
[      1.849][mmc]: mmc_config_clock: clk 25000000
[      1.864][mmc]: mmc re-update_phase
[      1.871][mmc]: mmc re-update_phase
[      1.878][mmc]: mmc re-update_phase
[      1.884][mmc]: ddr8 
[      1.888][mmc]: mmc re-update_phase
[      1.895][mmc]: mmc_config_clock: clk 25000000
[      1.905][mmc]: mmc_config_clock: clk 50000000
[      1.911][mmc]: CID 0x90014a48 0x38473461 0x92a110d2 0x802726b9
[      1.916][mmc]: MMC v5.1
[      1.919][mmc]: mmc clk 50000000
[      1.922][mmc]: SD/MMC Card: 8bit, capacity: 7456MB
[      1.927][mmc]: boot0 capacity: 4000KB,boot1 capacity: 4000KB
[      1.933][mmc]: ***SD/MMC 2 init OK!!!***
[      1.938][mmc]: erase_grp_size:0x400WrBlk * 0x200 = 0x80000 Byte
[      1.944][mmc]: secure_feature 0x55
[      1.947][mmc]: secure_removal_type  0x3b
[      1.951]sunxi flash init ok
In:    serial
Out:   serial
Err:   serial
--------fastboot partitions--------
-total partitions:15-
-name-        -start-       -size-      
bootloader  : 1000000       2000000     
env         : 3000000       1000000     
boot        : 4000000       1000000     
system      : 5000000       80000000    
verity_block: 85000000      2000000     
misc        : 87000000      1000000     
recovery    : 88000000      2000000     
cache       : 8a000000      30000000    
metadata    : ba000000      1000000     
private     : bb000000      1000000     
frp         : bc000000      80000       
empty       : bc080000      f80000      
alog        : bd000000      5000000     
media_data  : c2000000      1000000     
UDISK       : c3000000      0           
-----------------------------------
base bootcmd=run setargs_nand boot_normal
bootcmd set setargs_mmc
key 0
recovery key high 10, low 8
cant find fstbt value
misc partition found
to be run cmd=run setargs_mmc boot_normal

** Unable to use sunxi_flash 9:0 for fatload **
load file(ULI/factory/snum.txt) error 
serial is: 100001318804b21f5425
Net:   usb_etherWarning: failed to set MAC address

mount part name bootloader
cant open script.bin, maybe it is not exist
WORK_MODE_BOOT
board_status_probe
sunxi_bmp_logo_display
[      2.144][mmc]: blkcnt should not be 0
[      2.152]fetch script data boot_disp.output_disp fail
[      2.157]screen_id =0, screen_width =800, screen_height =1280
[      2.163]frame buffer address 46400036
read item0 copy0
Item0 (Map) magic is bad
the secure storage item0 copy0 is bad
read item0 copy1
Item0 (Map) magic is bad
the secure storage item0 copy0 == copy1, the data is good
the secure storage map is empty
no item name key_burned_flag in the map
sunxi secure storage has no flag
[      2.193]usb burn from boot
delay time 0
[      2.264]usb prepare ok
[      3.066]timer occur
[      3.068]overtime
[      3.103]do_burn_from_boot usb : no usb exist
limit to dc 
[      3.109]Hit any key to stop autoboot:  0 
read boot or recovery all
[      3.289]sunxi flash read :offset 4000000, 15023696 bytes OK
[      3.299]ready to boot
[      3.301][mmc]: mmc exit start
[      3.305][mmc]: mmc_config_clock: clk 50000000
[      3.310][mmc]: mmc_config_clock: clk 400000
[      3.325][mmc]: mmc 2 cmd 8 err 100
[      3.331][mmc]: mmc send if cond failed
[      3.336][mmc]: mmc 2 cmd 55 err 100
[      3.342][mmc]: send app cmd failed
[      3.359][mmc]: get sdc_phy_wipe fail.
[      3.363][mmc]: get sdc0 sdc_erase fail.
[      3.367][mmc]: get sdc_2xmode ok, val = 1
[      3.371][mmc]: get sdc_ddrmode ok, val = 1
[      3.375][mmc]: get sdc_f_max fail,use default  50000000Hz
[      3.381][mmc]: get card_line ok, card_line = 8
[      3.385][mmc]: get sdc_ex_dly_used fail,use default
[      3.390][mmc]: mmc 2 exit ok
[      3.393]
Starting kernel ...

[sun8i_fixup]: From boot, get meminfo:
	Start:	0x40000000
	Size:	2048MB
ion_carveout reserve: 96m@0 128m@0
ion_reserve_common: ion reserve: [0xb8000000, 0xc0000000]!
ion_cma reserve: 120m@0 176m@0 512m@0
ion_reserve_common: ion reserve: [0xa0000000, 0xc0000000]!
------sun8i_smp_init_ops----37-----
[    0.000000] Booting Linux on physical CPU 0
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.4.39 (guozh@WorldChip) (gcc version 4.6.3 20120201 (prerelease) (crosstool-NG linaro-1.13.1-2012.02-20120222 - Linaro GCC 2012.02) ) #31 SMP PREEMPT Thu Apr 11 10:30:31 CST 2019
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: sun8i
[    0.000000] Initialized persistent memory from 43084800-430947ff
[    0.000000] cma: CMA: reserved 512 MiB at a0000000
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] On node 0 totalpages: 524288
[    0.000000] free_area_init_node: node 0, pgdat c094fa00, node_mem_map c140a000
[    0.000000]   Normal zone: 1404 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 158340 pages, LIFO batch:31
[    0.000000]   HighMem zone: 3204 pages used for memmap
[    0.000000]   HighMem zone: 361340 pages, LIFO batch:31
[    0.000000] script_init enter!
[    0.000000] script_init exit!
[    0.000000] [mcpm_smp_init_cpus] ncores=8
[    0.000000] PERCPU: Embedded 8 pages/cpu @c262f000 s10752 r8192 d13824 u32768
[    0.000000] pcpu-alloc: s10752 r8192 d13824 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [0] 6 [0] 7 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 519680
[    0.000000] Kernel command line: boot_type=2 disp_para=100 fb_base=0x46400000 config_size=55900 androidboot.serialno=100001318804b21f5425 androidboot.hardware=sun8i console=ttyS0,115200 root=/dev/mmcblk0p7 init=/init vmalloc=384M ion_cma_list=120m,176m,512m loglevel=8 partitions=bootloader@mmcblk0p2:env@mmcblk0p5:boot@mmcblk0p6:system@mmcblk0p7:verity_block@mmcblk0p8:misc@mmcblk0p9:recovery@mmcblk0p10:cache@mmcblk0p11:metadata@mmcblk0p12:private@mmcblk0p13:frp@mmcblk0p14:empty@mmcblk0p15:alog@mmcblk0p16:media_data@mmcblk0p17:UDISK@mmcblk0p1 androidboot.selinux=enforcing
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 2048MB = 2048MB total
[    0.000000] Memory: 1537844k/1537844k available, 559308k reserved, 933888K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xe7800000 - 0xff000000   ( 376 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xe7000000   ( 624 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc087ad74   (8652 kB)
[    0.000000]       .init : 0xc087b000 - 0xc08cda00   ( 331 kB)
[    0.000000]       .data : 0xc08ce000 - 0xc09522f0   ( 529 kB)
[    0.000000]        .bss : 0xc0952914 - 0xc0adb010   (1570 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:544
[    0.000000] Architected local timer running at 24.00MHz.
[    0.000000] Switching to timer-based delay loop
[    0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[    0.000000] Console: colour dummy device 80x30
[    0.000250] Calibrating delay loop (skipped), value calculated using timer frequency.. 4800.00 BogoMIPS (lpj=24000000)
[    0.000275] pid_max: default: 32768 minimum: 301
[    0.000450] Security Framework initialized
[    0.000474] SELinux:  Initializing.
[    0.000555] SELinux:  Starting in permissive mode
[    0.000641] Mount-cache hash table entries: 512
[    0.001843] Initializing cgroup subsys debug
[    0.001861] Initializing cgroup subsys freezer
[    0.001904] CPU: Testing write buffer coherency: ok
[    0.001975] ftrace: allocating 22841 entries in 67 pages
[    0.030306] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.030358] Setting up static identity map for 0x405ee980 - 0x405ee9d8
[    0.031416] CPU1: Booted secondary processor
[    0.031416] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.031529] CPU2: Booted secondary processor
[    0.031529] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.031529] CPU3: Booted secondary processor
[    0.031529] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.040540] CPU4: failed to boot: -22
[    0.040650] CPU5: failed to boot: -22
[    0.040650] CPU6: failed to boot: -22
[    0.040650] CPU7: failed to boot: -22
[    0.040650] Brought up 4 CPUs
[    0.040650] SMP: Total of 4 processors activated (19200.00 BogoMIPS).
[    0.040733] devtmpfs: initialized
[    0.053523] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.054036] pinctrl core: initialized pinctrl subsystem
[    0.074777] NET: Registered protocol family 16
[    0.075956] DMA: preallocated 2048 KiB pool for atomic coherent allocations
[    0.075956] script_sysfs_init success
[    0.075956] sunxi_dump_init success
[    0.075956] gpiochip_add: registered GPIOs 0 to 383 on device: sunxi-pinctrl
[    0.076215] sunxi-pinctrl sunxi-pinctrl: initialized sunXi PIO driver
[    0.076622] gpiochip_add: registered GPIOs 1024 to 1031 on device: axp-pinctrl
[    0.077902] persistent_ram: uncorrectable error in header
[    0.077916] persistent_ram: no valid data in buffer (sig = 0xffffffff)
[    0.089486] console [ram-1] enabled
[    0.089896] [sunxi-module]: [sunxi-module.0] probe success
[    0.090411] Not Found clk pll_video1 in script 
[    0.090525] script config pll_ve to 432 Mhz
[    0.090707] Not Found clk pll_periph in script 
[    0.090811] script config pll_gpu to 432 Mhz
[    0.090916] script config pll_hsic to 480 Mhz
[    0.091101] script config pll_de to 504 Mhz
[    0.091200] sunxi_default_clk_init
[    0.091299] try to set pll6ahb1 to 200000000
[    0.091514] try to set ahb clk source to pll6ahb1
[    0.091614] set ahb clk source to pll6ahb1
[    0.091716] try to set ahb1 to 200000000
[    0.091820] try to set apb1 to 100000000
[    0.092933] ===fe3o4==== sunxi_root_procfs_attach ret:0
[    0.100600] bio: create slab <bio-0> at 0
[    0.100618] [ARISC] :sunxi-arisc driver v1.03
[    0.110115] [ARISC] :arisc version: [v0.1.79]
[    0.110721] sunxi_get_soc_bin: slow chip
[    0.111294] [ARISC] :sunxi-arisc driver v1.03 startup succeeded
[    0.120189] CPU4: Booted secondary processor
[    0.120189] CPU4: thread -1, cpu 0, socket 1, mpidr 80000100
[    0.130050] CPU5: Booted secondary processor
[    0.130050] CPU5: thread -1, cpu 1, socket 1, mpidr 80000101
[    0.130306] CPU6: Booted secondary processor
[    0.130306] CPU6: thread -1, cpu 2, socket 1, mpidr 80000102
[    0.140046] CPU7: Booted secondary processor
[    0.140046] CPU7: thread -1, cpu 3, socket 1, mpidr 80000103
[    0.140346] pwm module init!
[    0.141593] SCSI subsystem initialized
[    0.141593] usbcore: registered new interface driver usbfs
[    0.141593] usbcore: registered new interface driver hub
[    0.141593] usbcore: registered new device driver usb
[    0.141593] twi_chan_cfg()340 - [twi0] has no twi_regulator.
[    0.141593] twi_chan_cfg()340 - [twi1] has no twi_regulator.
[    0.141593] twi_chan_cfg()340 - [twi2] has no twi_regulator.
[    0.141593] twi_chan_cfg()332 - [twi3] has no twi_used!
[    0.141593] twi_chan_cfg()352 - [twi3] has no twi_used!
[    0.142344] Linux video capture interface: v2.00
[    0.190405] Advanced Linux Sound Architecture Driver Version 1.0.25.
[    0.191171] Bluetooth: Core ver 2.16
[    0.191312] NET: Registered protocol family 31
[    0.191413] Bluetooth: HCI device and connection manager initialized
[    0.191600] Bluetooth: HCI socket layer initialized
[    0.191703] Bluetooth: L2CAP socket layer initialized
[    0.191904] Bluetooth: SCO socket layer initialized
[    0.200245] cfg80211: Calling CRDA to update world regulatory domain
[    0.200669] Switching to clocksource arch_sys_counter
[    0.219499] FS-Cache: Loaded
[    0.219964] CacheFiles: Loaded
[    0.232255] axp81x_dcdc1: Failed to create debugfs directory
[    0.234059] NET: Registered protocol family 2
[    0.234477] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.235593] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.238227] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[    0.239878] TCP: Hash tables configured (established 131072 bind 65536)
[    0.240116] TCP: reno registered
[    0.240224] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.240446] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.240976] NET: Registered protocol family 1
[    0.241446] Unpacking initramfs...
[    0.544879] Freeing initrd memory: 4132K
[    0.547309] [pm]aw_pm_init!
[    0.547498] standby_mode = 0. 
[    0.547599] aw_pm_init: not support super standby. 
[    0.547700] wakeup src cnt is : 3. 
[    0.547886] pmu name: pmu1_para .
[    0.547991] pmu1_enable = 0x1. 
[    0.548091] pmux_id = 0x7. 
[    0.548192] pmu name: pmu2_para .
[    0.548372] config_pmux_para: script_parser_fetch err. 
[    0.548473] pmu2_enable = 0x0. 
[    0.548988] add_sys_pwr_dm: axp81x_aldo2 ldo already alwayson.
[    0.549323] add_sys_pwr_dm: axp81x_aldo2 ldo already alwayson.
[    0.549435] add_sys_pwr_dm: axp81x_aldo2 ldo already alwayson.
[    0.549618] after inited: sys_mask config = 0x6bd5. 
[    0.549720] dynamic_standby enalbe = 0x0. 
[    0.549952] sunxi_reg_init enter
[    0.550520] lock super standby for a83!
[    0.550628] lookup_scene_lock_name: new scene lock super_standby
[    0.550809] scene_lock_init name=super_standby
[    0.550912] scene_lock: super_standby, type 5, count 1
[    0.551705] audit: initializing netlink socket (disabled)
[    0.551872] type=2000 audit(0.550:1): initialized
[    0.552920] highmem bounce pool size: 64 pages
[    0.554629] NTFS driver 2.1.30 [Flags: R/W].
[    0.554939] fuse init (API version 7.18)
[    0.555687] msgmni has been set to 1187
[    0.555826] SELinux:  Registering netfilter hooks
[    0.558502] io scheduler noop registered
[    0.558689] io scheduler deadline registered
[    0.558906] io scheduler cfq registered (default)
[    0.560692] uart0: ttyS0 at MMIO 0x1c28000 (irq = 32) is a SUNXI
[    0.560800] sw_uart_pm()890 - uart0 clk is already enable
[    0.560993] sw_console_setup()1233 - console setup baud 115200 parity n bits 8, flow n
[    0.755570] console [ttyS0] enabled
[    0.854203] axp81x_dcdc1: Failed to create debugfs directory
[    0.952851] uart1: ttyS1 at MMIO 0x1c28400 (irq = 33) is a SUNXI
[    1.051579] axp81x_dcdc1: Failed to create debugfs directory
[    1.248158] uart2: ttyS2 at MMIO 0x1c28800 (irq = 34) is a SUNXI
[    1.346881] axp81x_dcdc1: Failed to create debugfs directory
[    1.666302] uart4: ttyS4 at MMIO 0x1c29000 (irq = 36) is a SUNXI
[    1.679091] loop: module loaded
[    1.683030] [rf_pm]: select module num is 9
[    1.687884] [rf_pm]: module power1 name vcc-wifi-io
[    1.693459] [rf_pm]: module power1 vol 3300000
[    1.698602] [rf_pm]: module power2 name 
[    1.703099] [rf_pm]: failed to fetch module_power2_vol
[    1.708941] [rf_pm]: module power3 name 
[    1.713517] [rf_pm]: failed to fetch module_power3_vol
[    1.719357] [rf_pm]: mod has no power_switch gpio
[    1.724809] [rf_pm]: mod has no chip_en gpio
[    1.729677] [rf_pm]: lpo_use_apclk: ac10032k2
[    1.734739] [rf_pm]: get power regulator  failed.
[    1.740195] [rf_pm]: set vcc-wifi-io to 3300000 v
[    1.745618] [rf_pm]: enable vcc-wifi-io.
[    1.750764] [rf_pm]: mod info power switch -1
[    1.755805] [rf_pm]: set ac10032k2 32k out
[    1.760612] scene_lock_init name=rf_pm
[    1.765272] [wifi_pm]: wifi gpio init is OK !!
[    1.770431] [rfkill]: mod has no ls_int gpio
[    1.775299] [rfkill]: mod has no pcm_ch gpio
[    1.781210] axp81x_dcdc1: Failed to create debugfs directory
[    1.787890] spi spi0: master is unqueued, this is deprecated
[    1.794529] tun: Universal TUN/TAP device driver, 1.6
[    1.800291] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    1.807633] PPP generic driver version 2.4.2
[    1.812720] PPP BSD Compression module registered
[    1.818150] PPP Deflate Compression module registered
[    1.825023] PPP MPPE Compression module registered
[    1.830506] NET: Registered protocol family 24
[    1.835652] PPTP driver version 0.8.5
[    1.840480] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.868074] sunxi-ehci sunxi-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.877162] sunxi-ehci sunxi-ehci.1: new USB bus registered, assigned bus number 1
[    1.887715] sunxi-ehci sunxi-ehci.1: irq 104, io mem 0xf1c1a000
[    1.910061] sunxi-ehci sunxi-ehci.1: USB 0.0 started, EHCI 1.00
[    1.916786] ehci_irq: highspeed device connect
[    1.921974] hub 1-0:1.0: USB hub found
[    1.926346] hub 1-0:1.0: 1 port detected
[    1.931321] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.958503] sunxi-ohci sunxi-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver
[    1.967198] sunxi-ohci sunxi-ohci.1: new USB bus registered, assigned bus number 2
[    1.975889] sunxi-ohci sunxi-ohci.1: irq 105, io mem 0xf1c1a400
[    2.044692] hub 2-0:1.0: USB hub found
[    2.048995] hub 2-0:1.0: 1 port detected
[    2.054078] usbcore: registered new interface driver cdc_acm
[    2.060606] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    2.069650] Initializing USB Mass Storage driver...
[    2.075399] usbcore: registered new interface driver usb-storage
[    2.082232] USB Mass Storage support registered.
[    2.087610] usbcore: registered new interface driver ums-alauda
[    2.094386] usbcore: registered new interface driver ums-cypress
[    2.101339] usbcore: registered new interface driver ums-datafab
[    2.108197] usbcore: registered new interface driver ums_eneub6250
[    2.115325] usbcore: registered new interface driver ums-freecom
[    2.122179] usbcore: registered new interface driver ums-isd200
[    2.129013] usbcore: registered new interface driver ums-jumpshot
[    2.136120] usbcore: registered new interface driver ums-karma
[    2.142809] usbcore: registered new interface driver ums-onetouch
[    2.149862] usbcore: registered new interface driver ums-realtek
[    2.156752] usbcore: registered new interface driver ums-sddr09
[    2.163614] usbcore: registered new interface driver ums-sddr55
[    2.170400] usbcore: registered new interface driver ums-usbat
[    2.177229] usbcore: registered new interface driver usbserial
[    2.183852] usbserial: USB Serial Driver core
[    2.188942] usbcore: registered new interface driver option
[    2.195287] USB Serial support registered for GSM modem (1-port)
[    2.250065] usb 1-1: new high-speed USB device number 2 using sunxi-ehci
[    2.402604] hub 1-1:1.0: USB hub found
[    2.407327] hub 1-1:1.0: 4 ports detected
[    2.414769] file system registered
[    2.420654] android_usb gadget: Mass Storage Function, version: 2009/09/11
[    2.428524] android_usb gadget: Number of LUNs=3
[    2.433802]  lun0: LUN: removable file: (no medium)
[    2.439432]  lun1: LUN: removable file: (no medium)
[    2.445002]  lun2: LUN: removable file: (no medium)
[    2.450951] get usb_serial_number success from boot command line
[    2.457583] android_usb gadget: android_usb ready
[    2.463725] axp81x_dcdc1: Failed to create debugfs directory
[    2.470298] sunxi_hcd_host0 sunxi_hcd_host0: sunxi_hcd host driver
[    2.477313] sunxi_hcd_host0 sunxi_hcd_host0: new USB bus registered, assigned bus number 3
[    2.487463] hub 3-0:1.0: USB hub found
[    2.491864] hub 3-0:1.0: 1 port detected
[    2.497381] mousedev: PS/2 mouse device common for all mice
[    2.504025] sunxikbd_script_init: key para not found, used default para. 
[    2.512475] sunxi_rtc_init(836): sunxi rtc device register!
[    2.519680] rtc_gettime(340): read time 1970-1-1 1:0:7
[    2.525961] alarm_gettime(477): get alarm time 1970-1-1 1:0:0 success!
[    2.533905] rtc_gettime(340): read time 1970-1-1 1:0:7
[    2.539998] rtc0 rtc0: rtc core: registered rtc0 as rtc0
[    2.546254] sunxi_rtc_probe(775)!
[    2.550199] pcf8563_init:
[    2.553279] rtc_detect,line:260
[    2.556877] rtc_detect,line:260
[    2.560490] rtc_detect: Detected chip pcf8563 at adapter 2, address 0x51
[    2.568175] get rtc_irq gpio failed
[    2.572186] pcf8563 2-0051: chip found, driver version 0.4.3
[    2.580530] pcf8563_get_datetime : [110]-[-1]-[0]-[1]-[53]-[35]
[    2.587249] pcf8563 2-0051: retrieved date/time is not valid.
[    2.596681] pcf8563_read_alarm: alm_tm is secs=0, mins=8, hours=0,mday=0, mon=-1, year=110, wday=0
[    2.608599] pcf8563_get_datetime : [110]-[-1]-[0]-[1]-[53]-[35]
[    2.615337] pcf8563 2-0051: retrieved date/time is not valid.
[    2.623657] pcf8563_get_datetime : [110]-[-1]-[0]-[1]-[53]-[35]
[    2.630394] pcf8563 2-0051: retrieved date/time is not valid.
[    2.637240] pcf8563 2-0051: rtc core: registered pcf8563 as rtc1
[    2.649140] ===fe3o4===pcf8563_probe:1132
[    2.653829] i2c /dev entries driver
[    2.658516] IR RC5(x) protocol handler initialized
[    2.664130] sunxi cedar version 0.1 
[    2.668373] [cedar]: install start!!!
[    2.672833] [cedar]: install end!!!
[    2.683020] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[    2.692945] Bluetooth: HCI UART driver ver 2.2
[    2.698009] Bluetooth: HCI H4 protocol initialized
[    2.703544] Bluetooth: HCI Realtek H5 protocol initialized
[    2.710315] sunxi_get_soc_bin: slow chip
[    2.717544] [mmc]: SD/MMC/SDIO Host Controller Driver(v1.122 2016-09-21 09:48) Compiled in Apr 11 2019 at 10:29:43
[    2.729196] [mmc]: get mmc1's sdc_power is null!
[    2.734401] [mmc]: get mmc2's 2xmode ok, val = 1
[    2.739578] [mmc]: get mmc2's ddrmode ok, val = 1
[    2.744921] [mmc]: MMC host used card: 0x7, boot card: 0x4, io_card 2
[    2.753160] [mmc]: sdc2 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.764125] [mmc]: sdc2 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.774261] [mmc]: sdc0 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.787378] [mmc]: sdc1 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.790036] [mmc]: sdc2 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.810850] [mmc]: *** sunxi_mci_dump_errinfo(L914): 
[    2.811846] usbcore: registered new interface driver usbhid
[    2.811853] usbhid: USB HID core driver
[    2.811861] zram: num_devices not specified. Using default: 1
[    2.811867] zram: Creating 1 devices ...
[    2.838143] smc 2 err, cmd 52,  RTO !!
[    2.842914] ashmem: initialized
[    2.843211] [mmc]: *** sunxi_mci_dump_errinfo(L914): smc 2 err, cmd 52,  RTO !!
[    2.843241] [mmc]: sdc2 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.845726] [mmc]: sdc2 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.847628] [mmc]: *** sunxi_mci_dump_errinfo(L914): smc 2 err, cmd 8,  RTO !!
[    2.847645] *******************Try sdio*******************
[    2.848470] [mmc]: *** sunxi_mci_dump_errinfo(L914): smc 2 err, cmd 5,  RTO !!
[    2.848488] mmc0: req failed (CMD5): -110, retrying...
[    2.849312] [mmc]: *** sunxi_mci_dump_errinfo(L914): smc 2 err, cmd 5,  RTO !!
[    2.849329] mmc0: req failed (CMD5): -110, retrying...
[    2.850155] [mmc]: *** sunxi_mci_dump_errinfo(L914): smc 2 err, cmd 5,  RTO !!
[    2.850173] mmc0: req failed (CMD5): -110, retrying...
[    2.850997] [mmc]: *** sunxi_mci_dump_errinfo(L914): smc 2 err, cmd 5,  RTO !!
[    2.851014] *******************Try sd *******************
[    2.851842] [mmc]: *** sunxi_mci_dump_errinfo(L914): smc 2 err, cmd 55,  RTO !!
[    2.852680] [mmc]: *** sunxi_mci_dump_errinfo(L914): smc 2 err, cmd 55,  RTO !!
[    2.853517] [mmc]: *** sunxi_mci_dump_errinfo(L914): smc 2 err, cmd 55,  RTO !!
[    2.854355] [mmc]: *** sunxi_mci_dump_errinfo(L914): smc 2 err, cmd 55,  RTO !!
[    2.854372] *******************Try mmc*******************
[    2.854380] [mmc]: sdc2 set ios: clk 400000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.854794] [mmc]: sdc2 set ios: clk 400000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.854878] [mmc]: sdc2 set ios: clk 400000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.854961] [mmc]: sdc2 set ios: clk 400000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.857429] [mmc]: sdc2 set ios: clk 400000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.891257] [mmc]: sdc2 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.903638] [mmc]: sdc2 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.904079] [mmc]: sdc2 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.904166] [mmc]: sdc2 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.904240] [mmc]: sdc2 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.904312] [mmc]: sdc2 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.904385] [mmc]: sdc2 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.904461] [mmc]: sdc2 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    2.904537] [mmc]: sdc2 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 1 timing MMC-HS(SDR20) dt B
[    2.904585] guozh### : mmc_init_card max_dtr = 200000000
[    2.904591] [mmc]: sdc2 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing MMC-HS(SDR20) dt B
[    2.904663] [mmc]: sdc2 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing MMC-HS(SDR20) dt B
[    2.904730] [mmc]: sdc2 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing MMC-HS(SDR20) dt B
[    2.904796] [mmc]: sdc2 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing MMC-HS(SDR20) dt B
[    2.904861] [mmc]: sdc2 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing MMC-HS(SDR20) dt B
[    2.904928] [mmc]: sdc2 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing MMC-HS(SDR20) dt B
[    2.904994] [mmc]: sdc2 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing MMC-HS(SDR20) dt B
[    2.905061] [mmc]: sdc2 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 8 timing MMC-HS(SDR20) dt B
[    2.905680] [mmc]: sdc2 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 8 timing MMC-HS(SDR20) dt B
[    2.905747] [mmc]: sdc2 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 8 timing MMC-HS(SDR20) dt B
[    2.905814] [mmc]: sdc2 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 8 timing MMC-HS(SDR20) dt B
[    2.905880] [mmc]: sdc2 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 8 timing MMC-HS(SDR20) dt B
[    2.905947] [mmc]: sdc2 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 8 timing MMC-HS(SDR20) dt B
[    2.906013] [mmc]: sdc2 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 8 timing MMC-HS(SDR20) dt B
[    2.906080] [mmc]: sdc2 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 8 timing MMC-HS(SDR20) dt B
[    2.906146] [mmc]: sdc2 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 8 timing MMC-HS(SDR20) dt B
[    2.906213] [mmc]: sdc2 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 8 timing UHS-DDR50 dt B
[    2.906263] [mmc]: sdc2 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 8 timing UHS-DDR50 dt B
[    2.906328] [mmc]: sdc2 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 8 timing UHS-DDR50 dt B
[    2.906393] [mmc]: sdc2 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 8 timing UHS-DDR50 dt B
[    2.906458] [mmc]: sdc2 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 8 timing UHS-DDR50 dt B
[    2.906528] mmc0: new high speed DDR MMC card at address 0001
[    2.906892] mmcblk0: mmc0:0001 H8G4a 7.28 GiB 
[    2.907084] mmcblk0boot0: mmc0:0001 H8G4a partition 1 4.00 MiB
[    2.907249] mmcblk0boot1: mmc0:0001 H8G4a partition 2 4.00 MiB
[    2.908960]  mmcblk0: p1 p2 p3 < p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 >
[    2.909006] mmcblk0: p1 size 8937472 extends beyond EOD, truncated
[    2.912138] [mmc]: sdc2 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 8 timing UHS-DDR50 dt B
[    2.914181]  mmcblk0boot1: unknown partition table
[    2.914741] [mmc]: sdc2 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 8 timing UHS-DDR50 dt B
[    2.916745]  mmcblk0boot0: unknown partition table
[    2.916946] *******************mmc init ok *******************
[    2.973123] logger: created 256K log 'log_main'
[    3.071191] logger: created 256K log 'log_events'
[    3.267250] logger: created 256K log 'log_radio'
[    3.446154] logger: created 256K log 'log_system'
[    3.451863] sunxi_oops: heming add OOPS_INFO_ADDR = -20
[    3.458077] usbcore: registered new interface driver snd-usb-audio
[    3.481669] asoc: ac100-aif1 <-> pri_dai mapping ok
[    3.487468] asoc: ac100-aif2 <-> bb-voice-dai mapping ok
[    3.497494] asoc: ac100-aif1 <-> sec_dai mapping ok
[    3.503309] asoc: ac100-aif3 <-> bb-voice-dai mapping ok
[    3.509549] asoc: ac100-aif2 <-> bb-voice-dai mapping ok
[    3.522631] asoc: sndhdmi <-> sunxi-hdmiaudio.0 mapping ok
[    3.529972] guozh### : set i2s1 clk end!!!
[    3.569735] asoc: sndi2s1 <-> i2s1 mapping ok
[    3.575583] u32 classifier
[    3.578712]     Actions configured
[    3.582567] Netfilter messages via NETLINK v0.30.
[    3.587943] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[    3.595300] ctnetlink v0.93: registering with nfnetlink.
[    3.601337] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[    3.609208] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[    3.616142] xt_time: kernel timezone is -0000
[    3.621251] IPv4 over IPv4 tunneling driver
[    3.626347] gre: GRE over IPv4 demultiplexor driver
[    3.631917] ip_gre: GRE over IPv4 tunneling driver
[    3.637857] ip_tables: (C) 2000-2006 Netfilter Core Team
[    3.644095] arp_tables: (C) 2002 David S. Miller
[    3.649364] TCP: cubic registered
[    3.653114] Initializing XFRM netlink socket
[    3.658259] NET: Registered protocol family 10
[    3.664205] Mobile IPv6
[    3.667004] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    3.673326] IPv6 over IPv4 tunneling driver
[    3.678935] NET: Registered protocol family 17
[    3.683971] NET: Registered protocol family 15
[    3.689210] Bluetooth: RFCOMM TTY layer initialized
[    3.694721] Bluetooth: RFCOMM socket layer initialized
[    3.700570] Bluetooth: RFCOMM ver 1.11
[    3.704797] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    3.710844] Bluetooth: BNEP filters: protocol multicast
[    3.716699] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    3.723834] ThumbEE CPU extension supported.
[    3.728665] Registering SWP/SWPB emulation handler
[    3.735678] rtc_gettime(340): read time 1970-1-1 1:0:8
[    3.741552] rtc0 rtc0: setting system clock to 1970-01-01 01:00:08 UTC (3608)
[    3.750480] sunxi_get_soc_bin: slow chip
[    3.755429] CPU Budget:Register notifier
[    3.759866] CPU Budget:register Success
[    3.764212] sunxi-budget-cooling sunxi-budget-cooling: Cooling device registered: thermal-budget-0
[    3.783413] =========GPS========= :gsp not used in configuration
[    3.790209] ALSA device list:
[    3.793570]   #0: sndac100
[    3.796638]   #1: sndhdmi
[    3.799614]   #2: sndi2s1
[    3.803309] Freeing init memory: 328K
[    3.809826] init: init started!
[    3.816013] init: init second stage started!
[    3.821476] init: waitpid failed: No child processes
[    3.827355] init: (Loading properties from /default.prop took 0.00s.)
[    3.836638] init: (Parsing /init.environ.rc took 0.00s.)
[    3.842925] init: (Parsing /init.usb.rc took 0.00s.)
[    3.849600] init: (Parsing init.sensors.rc took 0.00s.)
[    3.855531] init: (Parsing init.common.rc took 0.01s.)
[    3.861430] init: (Parsing init.sun8i.common.rc took 0.00s.)
[    3.868003] init: (Parsing init.sun8i.usb.rc took 0.00s.)
[    3.874101] init: (Parsing /init.sun8i.rc took 0.03s.)
[    3.880471] init: (Parsing /init.usb.configfs.rc took 0.00s.)
[    3.887044] init: (Parsing /init.zygote32.rc took 0.00s.)
[    3.893335] init: (Parsing /init.trace.rc took 0.00s.)
[    3.899146] init: (Parsing /init.rc took 0.06s.)
[    3.904607] init: Starting service 'ueventd'...
[    3.910387] init: Waiting for /dev/.coldboot_done...
[    3.912709] ueventd: ueventd started!
[    4.421054] ueventd: Coldboot took 0.51s.
[    4.423974] init: Waiting for /dev/.coldboot_done took 0.51s.
[    4.424036] init: /dev/hw_random not found
[    4.439041] init: write_file: Unable to open '/proc/sys/kernel/hung_task_timeout_secs': No such file or directory
[    4.450732] init: write_file: Unable to open '/proc/sys/kernel/sched_tunable_scaling': No such file or directory
[    4.462279] init: write_file: Unable to open '/proc/sys/kernel/sched_latency_ns': No such file or directory
[    4.473296] init: write_file: Unable to open '/proc/sys/kernel/sched_wakeup_granularity_ns': No such file or directory
[    4.485376] init: write_file: Unable to open '/proc/sys/kernel/sched_compat_yield': No such file or directory
[    4.590270] init: write_file: Unable to write to '/dev/cpuctl/cpu.shares': Invalid argument
[    4.601232] init: write_file: Unable to open '/proc/sys/abi/swp': No such file or directory
[    4.611296] init: /dev/hw_random not found
[    4.641843] [NAND]nand init start, nand0_used_flag is 0
[    4.647740] [NAND]nand driver is disabled 
[    4.654603] [mmc]: sdc2 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 8 timing UHS-DDR50 dt B
[    4.675466] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: barrier=1
[    4.685064] fs_mgr: __mount(source=/dev/block/by-name/system,target=/system,type=ext4)=0
[    4.695221] EXT4-fs (mmcblk0p11): VFS: Can't find ext4 filesystem
[    4.850094] fs_mgr: check_fs(): mount(/dev/block/by-name/cache,/cache,ext4)=-1: Invalid argument
[    4.861526] fs_mgr: Running /system/bin/e2fsck on /dev/block/by-name/cache
[    4.942585] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
[    4.942591] 
[    4.949466] e2fsck: ext2fs_open2: Bad magic number in super-block
[    4.949470] 
[    4.958108] e2fsck: /system/bin/e2fsck: Superblock invalid, trying backup blocks...
[    4.958112] 
[    4.968482] e2fsck: /system/bin/e2fsck: Bad magic number in super-block while trying to open /dev/block/by-name/cache
[    4.968487] 
[    4.982156] e2fsck: 
[    4.982159] 
[    4.986365] e2fsck: 
[    4.986367] 
[    4.990584] e2fsck: The superblock could not be read or does not describe a correct ext2
[    4.990589] 
[    5.001441] e2fsck: filesystem.  If the device is valid and it really contains an ext2
[    5.001445] 
[    5.012314] e2fsck: filesystem (and not swap or ufs or something else), then the superblock
[    5.012321] 
[    5.023545] e2fsck: is corrupt, and you might try running e2fsck with an alternate superblock:
[    5.023551] 
[    5.035019] e2fsck:     e2fsck -b 8193 <device>
[    5.035022] 
[    5.041860] e2fsck: 
[    5.041863] 
[    5.046071] e2fsck: e2fsck terminated by exit(8)
[    5.046075] 
[    5.054216] EXT4-fs (mmcblk0p11): VFS: Can't find ext4 filesystem
[    5.170082] fs_mgr: __mount(source=/dev/block/by-name/cache,target=/cache,type=ext4)=-1
[    5.180122] fs_mgr: fs_mgr_mount_all(): /dev/block/by-name/cache is wiped and /cache ext4 is formattable. Format it.
[    5.192020] fs_mgr: fs_mgr_do_format: Format /dev/block/by-name/cache as 'ext4'.
[    5.712943] EXT4-fs (mmcblk0p11): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
[    5.725011] fs_mgr: check_fs(): mount(/dev/block/by-name/cache,/cache,ext4)=0: Success
[    5.880061] fs_mgr: check_fs(): unmount(/cache) succeeded
[    5.886167] fs_mgr: Running /system/bin/e2fsck on /dev/block/by-name/cache
[    5.919036] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
[    5.919040] 
[    5.925926] e2fsck: /dev/block/by-name/cache: clean, 11/49152 files, 6355/196608 blocks
[    5.925931] 
[    5.943077] EXT4-fs (mmcblk0p11): mounted filesystem with ordered data mode. Opts: barrier=1,data=ordered,nomblk_io_submit,noauto_da_alloc,errors=panic
[    5.958462] fs_mgr: __mount(source=/dev/block/by-name/cache,target=/cache,type=ext4)=0
[    5.968323] EXT4-fs (mmcblk0p16): VFS: Can't find ext4 filesystem
[    6.110104] fs_mgr: check_fs(): mount(/dev/block/by-name/alog,/logger,ext4)=-1: Invalid argument
[    6.120070] fs_mgr: Running /system/bin/e2fsck on /dev/block/by-name/alog
[    6.151092] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
[    6.151096] 
[    6.157917] e2fsck: ext2fs_open2: Bad magic number in super-block
[    6.157921] 
[    6.166531] e2fsck: /system/bin/e2fsck: Superblock invalid, trying backup blocks...
[    6.166535] 
[    6.176893] e2fsck: /system/bin/e2fsck: Bad magic number in super-block while trying to open /dev/block/by-name/alog
[    6.176898] 
[    6.190431] e2fsck: 
[    6.190433] 
[    6.194629] e2fsck: 
[    6.194631] 
[    6.198825] e2fsck: The superblock could not be read or does not describe a correct ext2
[    6.198829] 
[    6.209660] e2fsck: filesystem.  If the device is valid and it really contains an ext2
[    6.209665] 
[    6.220313] e2fsck: filesystem (and not swap or ufs or something else), then the superblock
[    6.220318] 
[    6.231436] e2fsck: is corrupt, and you might try running e2fsck with an alternate superblock:
[    6.231441] 
[    6.242856] e2fsck:     e2fsck -b 8193 <device>
[    6.242859] 
[    6.249663] e2fsck: 
[    6.249665] 
[    6.253928] e2fsck: e2fsck terminated by exit(8)
[    6.253932] 
[    6.261899] EXT4-fs (mmcblk0p16): VFS: Can't find ext4 filesystem
[    6.380067] fs_mgr: __mount(source=/dev/block/by-name/alog,target=/logger,type=ext4)=-1
[    6.390082] fs_mgr: fs_mgr_mount_all(): /dev/block/by-name/alog is wiped and /logger ext4 is formattable. Format it.
[    6.401870] fs_mgr: fs_mgr_do_format: Format /dev/block/by-name/alog as 'ext4'.
[    6.617902] EXT4-fs (mmcblk0p16): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
[    6.629980] fs_mgr: check_fs(): mount(/dev/block/by-name/alog,/logger,ext4)=0: Success
[    6.790074] fs_mgr: check_fs(): unmount(/logger) succeeded
[    6.796270] fs_mgr: Running /system/bin/e2fsck on /dev/block/by-name/alog
[    6.827870] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
[    6.827874] 
[    6.834739] e2fsck: /dev/block/by-name/alog: clean, 11/5120 files, 1358/20480 blocks
[    6.834744] 
[    6.851562] EXT4-fs (mmcblk0p16): mounted filesystem with ordered data mode. Opts: barrier=1,data=ordered,nomblk_io_submit,noauto_da_alloc,errors=panic
[    6.866917] fs_mgr: __mount(source=/dev/block/by-name/alog,target=/logger,type=ext4)=0
[    6.876783] EXT4-fs (mmcblk0p1): VFS: Can't find ext4 filesystem
[    7.000081] fs_mgr: check_fs(): mount(/dev/block/by-name/UDISK,/data,ext4)=-1: Invalid argument
[    7.009862] fs_mgr: Running /system/bin/e2fsck on /dev/block/by-name/UDISK
[    7.041918] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
[    7.041922] 
[    7.048833] e2fsck: ext2fs_open2: Bad magic number in super-block
[    7.048837] 
[    7.057432] e2fsck: /system/bin/e2fsck: Superblock invalid, trying backup blocks...
[    7.057436] 
[    7.068847] e2fsck: /system/bin/e2fsck: Bad magic number in super-block while trying to open /dev/block/by-name/UDISK
[    7.068853] 
[    7.082523] e2fsck: 
[    7.082526] 
[    7.086728] e2fsck: 
[    7.086730] 
[    7.091014] e2fsck: The superblock could not be read or does not describe a correct ext2
[    7.091019] 
[    7.101869] e2fsck: filesystem.  If the device is valid and it really contains an ext2
[    7.101873] 
[    7.112489] e2fsck: filesystem (and not swap or ufs or something else), then the superblock
[    7.112493] 
[    7.123655] e2fsck: is corrupt, and you might try running e2fsck with an alternate superblock:
[    7.123660] 
[    7.135113] e2fsck:     e2fsck -b 8193 <device>
[    7.135117] 
[    7.141987] e2fsck: 
[    7.141990] 
[    7.146192] e2fsck: e2fsck terminated by exit(8)
[    7.146195] 
[    7.154178] EXT4-fs (mmcblk0p1): VFS: Can't find ext4 filesystem
[    7.290074] fs_mgr: __mount(source=/dev/block/by-name/UDISK,target=/data,type=ext4)=-1
[    7.300046] fs_mgr: fs_mgr_mount_all(): /dev/block/by-name/UDISK is wiped and /data ext4 is formattable. Format it.
[    7.311883] fs_mgr: fs_mgr_mount_all(): also wipe /dev/block/by-name/metadata
[    7.319952] +mmc_blk_issue_secdiscard_rq,1836
[    7.324940] mmc0:mmc_do_erase: erase from 6135808 to 6168575 arg 0x80000000
[    7.336034] -mmc_blk_issue_secdiscard_rq,1890
[    7.336039] fs_mgr: fs_mgr_do_format: Format /dev/block/by-name/UDISK as 'ext4'.
[    9.796040] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
[    9.808021] fs_mgr: check_fs(): mount(/dev/block/by-name/UDISK,/data,ext4)=0: Success
[    9.960080] fs_mgr: check_fs(): unmount(/data) succeeded
[    9.966089] fs_mgr: Running /system/bin/e2fsck on /dev/block/by-name/UDISK
[   10.007580] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
[   10.007585] 
[   10.014513] e2fsck: /dev/block/by-name/UDISK: clean, 11/276352 files, 36791/1104896 blocks
[   10.014518] 
[   10.031798] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: barrier=1,data=ordered,nomblk_io_submit,noauto_da_alloc,errors=panic
[   10.047103] fs_mgr: __mount(source=/dev/block/by-name/UDISK,target=/data,type=ext4)=0
[   10.293402] Adding 131068k swap on /dev/block/zram0.  Priority:-1 extents:1 across:131068k SS
[   10.304213] FAT-fs (mmcblk0p17): bogus number of reserved sectors
[   10.311114] FAT-fs (mmcblk0p17): Can't find a valid FAT filesystem
[   10.439382] enter tr_probe
[   10.442523] exit tr_probe
[   10.598093] [DISP]disp_module_init
[   10.602957] cmdline,disp=100
[   10.673743] [DISP]disp_module_init finish
[   10.699302] cmdline,disp=100
[   11.300113] [DISP] disp_hdmi_set_detect,line:405:hdmi1's mgr is NULL
[   11.371318] PVR_K: Get gpu regulator successfully.
[   11.376856] PVR_K: Enable gpu external power successfully.
[   11.383034] sunxi_get_soc_bin: slow chip
[   11.387561] PVR_K: Get gpu pll_gpu clock id successfully
[   11.393562] PVR_K: Get gpu core clock id successfully
[   11.399252] PVR_K: Get gpu mem clock id successfully
[   11.404917] PVR_K: Get gpu hyd clock id successfully
[   11.410528] PVR_K: Set the parent of gpu core clock to pll_gpu.
[   11.417231] PVR_K: Set the parent of gpu mem clock to pll_gpu.
[   11.423817] PVR_K: Set the parent of gpu hyd clock to pll_gpu.
[   11.430517] PVR_K: The frequency of gpu pll_gpu clock has been set to 552 MHz
[   11.438588] PVR_K: The frequency of gpu core clock has been set to 552 MHz
[   11.446318] PVR_K: The frequency of gpu mem clock has been set to 552 MHz
[   11.454057] PVR_K: The frequency of gpu hyd clock has been set to 552 MHz
[   11.463770] PVR_K: Release gpu hyd clock reset successfully.
[   11.476979] [fm1288] : fm1288_init
[   11.480961] i2c i2c-0: fm1288_ctl detection function provided no name for 0x60
[   11.489096] [fm1288] : I2C detect success
[   11.493739] [fm1288] : fm1288_rst
[   11.518132] twi_stop()471 - [i2c1] i2c state isn't idle(0xf8)
[   11.524618] sunxi_i2c_core_process()833 - [i2c1] STOP failed!
[   11.528072] sunxi_i2c_do_xfer()985 - [i2c1] incomplete xfer (status: 0x38, dev addr: 0x60)
[   11.540578] sunxi_i2c_do_xfer()985 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x60)
[   11.549912] [fm1288] : fm1288_i2c_write:I2C retry timeout, reset chip.
[   11.557096] i2c i2c-2: fm1288_ctl detection function provided no name for 0x60
[   11.579190] ***CTP***GTP driver init
[   11.583262] =====ctp_fetch_sysconfig_para=====. 
[   11.588527] ctp_fetch_sysconfig_para: ctp_power_io script_get_item err. 
[   11.596077] ctp_irq gpio number is 359
[   11.620034] ***CTP***info.ctp_used:1
[   11.624079] ***CTP***info.twi_id:0
[   11.627918] ***CTP***info.screen_max_x:800
[   11.632610] ***CTP***info.screen_max_y:1280
[   11.637333] ***CTP***info.revert_x_flag:1
[   11.641872] ***CTP***info.revert_y_flag:0
[   11.646453] ***CTP***info.exchange_x_y_flag:1
[   11.651376] ***CTP***info.irq_gpio_number:359
[   11.656352] ***CTP***info.wakeup_gpio_number:358
[   11.661563] ***CTP******CTP*** ctp_wakeup:status:0,ms = 0
[   11.730058] ***CTP******CTP*** ctp_wakeup:status:1,ms = 0
[   11.830293] the adapter number is 0
[   11.834248] ctp_detect: addr = 5d
[   11.838688] detect ret 2
[   11.841591] ======detect ok !=====
[   11.845573] ***CTP***GTP Driver Version: V2.2<2014/01/14>***CTP***GTP Driver Built@10:29:47, Apr 11 2019***CTP***GTP I2C Address: 0x5d<<-GTP-INFO->> IC Version: 911_1060
[   11.864500] ***CTP***Config Groups Lengths: 186, 186, 186, 186, 186, 186
[   11.873353] ***CTP***CTP name : gt9271_noah
[   11.878049] ***CTP***gt9xx:sensor_id = 4
[   11.882544] ***CTP***Sensor_ID: 4***CTP***CTP_CONFIG_GROUP5 used, config length: 186
[   11.892564] ***CTP***CFG_GROUP5 Config Version: 0, 0x00; IC Config Version: 65, 0x41
[   11.901291] <<-GTP-INFO->> Driver send config.
[   11.929074] <<-GTP-INFO->> X_MAX: 1280, Y_MAX: 800, TRIGGER: 0x01
[   11.950061] <<-GTP-INFO->> create proc entry gt9xx_config success
[   11.956969] <<-GTP-INFO->> Ready to run update thread.
[   11.962860] <<-GTP-INFO->> Update by default firmware array
[   11.963231] <<-GTP-INFO->> GTP works in polling mode.
[   11.963240] <<-GTP-INFO->> Applied memory size:2562.
[   11.963246] <<-GTP-INFO->> I2C function: without pre and end cmd!
[   11.963269] <<-GTP-INFO->> Create proc entry success!
[   11.963306] the adapter number is 1
[   11.963315] the adapter number is 2
[   11.968184] sunxigk_init 
[   11.968197] sunxigk_script_init power key io number = 361.
[   11.968203] sunxigk_script_init volumeup key io number = 363.
[   11.968208] sunxigk_script_init volumedown key io number = 362.
[   11.968214] sunxigk_script_init sos key io number = 360.
[   11.968942] sunxikbd_init end
[   11.985741] [VFE]cci probe start cci_sel = 0!
[   11.985781] [VFE]cci probe end cci_sel = 0!
[   11.985856] [VFE]cci_init end
[   12.042983] [VFE]Welcome to Video Front End driver
[   12.043439] [VFE]pdev->id = 0
[   12.043443] [VFE]dev->mipi_sel = 0
[   12.043447] [VFE]dev->vip_sel = 0
[   12.043450] [VFE]dev->isp_sel = 0
[   12.049629] [VFE_WARN]vfe vpu clock is null
[   12.070671] <<-GTP-INFO->> FILE HARDWARE INFO:00016000
[   12.072771] [ISP] isp platform_id = 4!
[   12.072875] [VFE]vfe_init end
[   12.080040] [VFE]probe_work_handle start!
[   12.080046] [VFE]..........................vfe clk open!.......................
[   12.080330] [VFE]v4l2 subdev register input_num = 0
[   12.080505] [VFE]vfe sensor detect start! input_num = 0
[   12.080514] [VFE]Find sensor name is "ov5648", i2c address is 6c, type is "RAW" !
[   12.080520] [VFE]Sub device register "ov5648" i2c_addr = 0x6c start!
[   12.080529] [VFE]v4l2_device_register_subdev return 0
[   12.080534] [VFE]registered sensor subdev is OK!
[   12.080537] [VFE]Check sensor!
[   12.080542] [OV5648]CSI_SUBDEV_PWR_ON!
[   12.146982] <<-GTP-INFO->> FILE PID:9271
[   12.151448] <<-GTP-INFO->> FILE VID:1040
[   12.155980] <<-GTP-INFO->> IC HARDWARE INFO:00900600
[   12.161658] <<-GTP-INFO->> IC PID:911
[   12.165864] <<-GTP-INFO->> IC VID:1060
[   12.170240] <<-GTP-INFO->> Firmware length:90112(88K)
[   12.175990] <<-GTP-ERROR->> File PID != Ic PID, update aborted!
[   12.182794] <<-GTP-ERROR->> [update_proc]Check *.bin file fail.
[   12.200318] dhd_module_init: in
[   12.203924] ======== dhd_wlan_init_plat_data ========
[   12.209614] dhd_wlan_init_gpio: GPIO(WL_REG_ON) = -1
[   12.215028] [VFE]mclk on
[   12.218129] dhd_wlan_init_gpio: GPIO(WL_HOST_WAKE) = 355
[   12.224178] dhd_wlan_init_gpio: host_oob_irq: 3
[   12.229277] dhd_wlan_init_gpio: host_oob_irq_flags=0x414
[   12.235311] dhd_wifi_platform_load: Enter
[   12.237091] [OV5648]sensor_init
[   12.237359] [VFE CCI_0 ERR] Status error at addr_8bit = 6c, wr_flag = 1, val = ce60a30
[   12.237622] [VFE CCI_0 ERR] Status error at addr_8bit = 6c, wr_flag = 1, val = c000a30
[   12.237883] [VFE CCI_0 ERR] Status error at addr_8bit = 6c, wr_flag = 1, val = c000a30
[   12.237892] [OV5648]sensor read retry=2
[   12.237897] [OV5648]error at sensor_detect
[   12.237901] [OV5648]chip found is not an target chip.
[   12.237907] [OV5648]CSI_SUBDEV_PWR_OFF!
[   12.244130] [VFE]mclk off
[   12.256496] [VFE]vfe sensor subdev unregister!
[   12.256503] [VFE]Sub device register "ov5648" failed!
[   12.256508] [VFE_ERR]vfe sensor register check error at input_num = 0
[   12.257630] [VFE]read ini start
[   12.257690] [VFE]Fetch ini file form "/system/etc/hawkview/ov5648/isp_test_param.ini"
[   12.261539] [VFE]Fetch ini file form "/system/etc/hawkview/ov5648/isp_3a_param.ini"
[   12.266756] [VFE]Fetch ini file form "/system/etc/hawkview/ov5648/isp_iso_param.ini"
[   12.271503] [VFE]Fetch ini file form "/system/etc/hawkview/ov5648/isp_tuning_param.ini"
[   12.286056] [VFE]Fetch table form "/system/etc/hawkview/ov5648/bin/gamma_tbl.bin", gamma num = 1
[   12.287642] [VFE]registered actuator device succeed! act_name is ad5820_act
[   12.287659] [VFE]V4L2 device registered as vfe-0
[   12.287709] [VFE]register_early_suspend @ probe handle!
[   12.287715] [VFE]..........................vfe clk close!.......................
[   12.287741] [VFE]probe_work_handle end!
[   12.386120] Power-up adapter 'DHD generic adapter'
[   12.395371] wifi_platform_set_power = 1
[   12.399707] ======== PULL WL_REG_ON(-1) HIGH! ========
[   12.405496] [wifi_pm]: wifi power on
[   12.710038] wifi_platform_bus_enumerate device present 1
[   12.716030] ======== Card detection to detect SDIO card! ========
[   12.722976] [mmc]: sdc1 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[   12.734279] [mmc]: sdc1 power_supply is null
[   12.760025] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[   12.797370] [mmc]: *** sunxi_mci_dump_errinfo(L914): smc 1 err, cmd 52,  RTO !!
[   12.806449] [mmc]: *** sunxi_mci_dump_errinfo(L914): smc 1 err, cmd 52,  RTO !!
[   12.814765] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[   12.827564] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[   12.839781] [mmc]: *** sunxi_mci_dump_errinfo(L914): smc 1 err, cmd 8,  RTO !!
[   12.847940] *******************Try sdio*******************
[   12.854515] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[   12.874999] mmc2: queuing unknown CIS tuple 0x80 (2 bytes)
[   12.882822] mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
[   12.890583] mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
[   12.899664] mmc2: queuing unknown CIS tuple 0x80 (7 bytes)
[   12.909333] mmc2: queuing unknown CIS tuple 0x81 (9 bytes)
[   12.967956] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B
[   12.978216] [mmc]: sdc1 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B
[   12.988716] [mmc]: sdc1 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B
[   13.001971] mmc2: queuing unknown CIS tuple 0x91 (3 bytes)
[   13.008238] mmc2: new high speed SDIO card at address 0001
[   13.015113] *******************sdio init ok*******************
[   13.031117] bcmsdh_register: register client driver
[   13.036684] bcmsdh_sdmmc: bcmsdh_sdmmc_probe Enter
[   13.042247] bcmsdh_sdmmc: bcmsdh_sdmmc_probe Enter
[   13.047655] bus num (host idx)=2, slot num (rca)=1
[   13.053064] found adapter info 'DHD generic adapter'
[   13.058734] sdioh_attach: set sd_f2_blocksize 128
[   13.064322] dhdsdio_probe : no mutex held. set lock
[   13.069951] F1 signature read @0x18000000=0x15264345
[   13.078275] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[   13.086063] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[   13.093859] dhd_conf_set_chiprev: chip=0x4345, chiprev=6
[   13.099928] dhd_conf_set_conf_path_by_nv_path: config_path=/system/vendor/modules/config.txt
[   13.110677] dhd_conf_read_config: dhd_slpauto = 0
[   13.116883] wl_create_event_handler(): thread:wl_event_handler:b1 started
[   13.116891] tsk Enter, tsk = 0xe0641410
[   13.129740] p2p0: P2P Interface Registered
[   13.134472] dhd_attach(): thread:dhd_watchdog_thread:b2 started
[   13.141269] dhd_attach(): thread:dhd_dpc:b3 started
[   13.146835] dhd_attach(): thread:dhd_rxf:b4 started
[   13.152403] dhd_deferred_work_init: work queue initialized 
[   13.167328] Dongle Host Driver, version 1.201.59.11 (r506368)
[   13.167332] Compiled in drivers/net/wireless/bcmdhd on Apr 11 2019 at 10:30:01
[   13.182531] Register interface [wlan0]  MAC: 6c:21:a2:4a:b7:be
[   13.182535] 
[   13.190852] dhd_prot_ioctl : bus is down. we have nothing to do
[   13.197609] bcmsdh_oob_intr_unregister: Enter
[   13.202540] bcmsdh_oob_intr_unregister: irq is not registered
[   13.209024] dhd_txglom_enable: enable 0
[   13.213414] dhd_conf_set_txglom_params: swtxglom=0, txglom_ext=0
[   13.220178] dhd_conf_set_txglom_params: txglom_bucket_size=0
[   13.226600] dhd_conf_set_txglom_params: txglomsize=0, deferred_tx_len=0, bus_txglom=-1
[   13.235575] dhd_conf_set_txglom_params: tx_in_rx=1, tx_max_offset=0, txctl_tmo_fix=1
[   13.244284] sdioh_set_mode: set txglom_mode to multi-desc
[   13.250472] dhd_bus_devreset:  WLAN OFF DONE
[   13.255307] wifi_platform_set_power = 0
[   13.259672] ======== PULL WL_REG_ON(-1) LOW! ========
[   13.265426] [wifi_pm]: wifi power off
[   13.269571] dhdsdio_probe : the lock is released.
[   13.274976] dhd_module_init: Exit err=0
[   13.287487] Bluetooth: MSM Sleep Mode Driver Ver 1.2
[   13.293255] Bluetooth: has no bt_wake_invert
[   13.293259] 
[   13.316161] usbcore: registered new interface driver asix
[   13.329149] usbcore: registered new interface driver qf9700
[   13.342354] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[   13.357198] usbcore: registered new interface driver cdc_ether
[   13.371533] usbcore: registered new interface driver smsc75xx
[   13.385508] usbcore: registered new interface driver smsc95xx
[   13.392931] [BT_LPM] bluesleep_get_uart_port: bluesleep_get_uart_port get uart_port from blusleep_uart_dev: uart, port irq: 33
[   13.406247] init: Starting service 'logd'...
[   13.422107] init: (Loading properties from /system/build.prop took 0.01s.)
[   13.430057] init: (Loading properties from /vendor/build.prop took 0.00s.)
[   13.437909] init: (Loading properties from /factory/factory.prop took 0.00s.)
[   13.446328] init: /recovery not specified in fstab
[   13.451870] init: void property_opt_for_mem(): start!
[   13.457665] logd.auditd: start
[   13.458811] get_item_store: input buf lcd0_para lcd_x
[   13.458822] get_item_store: get "lcd0_para"->"lcd_x"
[   13.458842] get_item_show(804): script_get_item return type [int] for lcd0_para->lcd_x
[   13.458852] get_item_store: input buf lcd0_para lcd_y
[   13.458857] get_item_store: get "lcd0_para"->"lcd_y"
[   13.458865] get_item_show(804): script_get_item return type [int] for lcd0_para->lcd_y
[   13.458985] init: void property_opt_for_mem(): width_dp = 800; height_dp = 1280; screenSize = 3; bSupport64Bit = 0, g_total_mem = 2018 
[   13.475012] init: void property_opt_for_mem(): end!
[   13.475920] init: Starting service 'vold'...
[   13.476841] init: Not bootcharting.
[   13.477524] init: Failed to reload policy
[   13.477755] init: Starting service 'exec 0 (/system/bin/tzdatacheck)'...
[   13.510902] init: Service 'exec 0 (/system/bin/tzdatacheck)' (pid 193) exited with status 0
[   13.535164] init: Starting service 'bootclone'...
[   13.536148] init: (Loading properties from /data/local.prop took 0.00s.)
[   13.536203] init: Unable to open persistent property directory "/data/property": No such file or directory
[   13.536282] init: Starting service 'logd-reinit'...
[   13.540768] init: Starting service 'healthd'...
[   13.541676] init: Starting service 'lmkd'...
[   13.542676] init: Starting service 'servicemanager'...
[   13.543864] init: Starting service 'surfaceflinger'...
[   13.545639] init: Starting service 'pvrsrvctl'...
[   13.546176] binder: 202:202 transaction failed 29189, size 0-0
[   13.546536] init: Starting service 'sayeye'...
[   13.549029] rtc_gettime(340): read time 1970-1-1 1:0:18
[   13.549200] init: Starting service 'zygote'...
[   13.551337] logd.klogd: 13551281674
[   13.552103] init: Starting service 'console'...
[   13.553841] init: Starting service 'encrypt'...
[   13.555079] android_usb: already disabled
[   13.555652] init: Starting service 'adbd'...
[   13.561499] adb_open
[   13.561513] mtp_bind_config
[   13.561534] ep_matches, wrn: endpoint already claimed, ep(0xc091e094, 0xe61ebe00, ep1in-bulk)
[   13.561542] ep_matches, wrn: endpoint already claimed, ep(0xc091e094, 0xe61ebe00, ep1in-bulk)
[   13.561551] ep_matches, wrn: endpoint already claimed, ep(0xc091e0e0, 0xe61ebe00, ep1out-bulk)
[   13.561558] gadget_is_softwinner_otg is not -int
[   13.561563] gadget_is_softwinner_otg is not -int
[   13.561605] adb_bind_config
[   13.561612] ep_matches, wrn: endpoint already claimed, ep(0xc091e094, 0xe61ebe00, ep1in-bulk)
[   13.561619] ep_matches, wrn: endpoint already claimed, ep(0xc091e0e0, 0xe61ebe00, ep1out-bulk)
[   13.561627] ep_matches, wrn: endpoint already claimed, ep(0xc091e094, 0xe61ebe00, ep1in-bulk)
[   13.561633] ep_matches, wrn: endpoint already claimed, ep(0xc091e0e0, 0xe61ebe00, ep1out-bulk)
[   13.561640] ep_matches, wrn: endpoint already claimed, ep(0xc091e12c, 0xe61c8900, ep2in-bulk)
[   13.561935] logd.daemon: reinit
[   13.563406] init: Service 'logd-reinit' (pid 199) exited with status 0
[   13.737803] init: Service 'zygote' is being killed...
[   13.739613] init: Service 'zygote' (pid 212) killed by signal 9
[   13.739638] init: Service 'zygote' (pid 212) killing any children in process group
[   13.740430] init: Not bootcharting.
[   13.742296] init: Failed to reload policy
[   13.742565] init: Starting service 'exec 1 (/system/bin/tzdatacheck)'...
[   13.759105] init: Service 'exec 1 (/system/bin/tzdatacheck)' (pid 239) exited with status 0
[   13.760213] init: property_set("ro.bt.bdaddr_path", "/data/misc/bluetooth/bdaddr") failed
[   13.762505] PVR_K: UM DDK-(3793329) and KM DDK-(3793329) match. [ OK ]
[   13.779881] init: Service 'pvrsrvctl' (pid 208) exited with status 0
[   13.851991] init: Service 'bootclone' (pid 198) exited with status 0
shell@octopus-f1:/ $ [   13.924799] init: Starting service 'bootanim'...
[   14.328531] sunxi_snddaudio_hw_params,line:62,freq_in:22579200,daudio_pcm_select:1,audio_format:1,signal_inversion:1
[   14.543881] [DISP] ready enter pm_runtime_get_sync, device0
[   20.750444] CPU Budget: Temperature: 52 Limit state:1 item[1608000,4,1608000,4 0]
[   21.770253] CPU Budget: Temperature: 54 Limit state:0 item[1800000,4,1800000,4 0]
[   22.280168] CPU Budget: Temperature: 49 Limit state:0 item[1800000,4,1800000,4 0]
[   22.780184] CPU Budget: Temperature: 55 Limit state:1 item[1608000,4,1608000,4 0]
[   23.420090] [BT_LPM] bluesleep_tx_timer_expire: Tx timer expired
[   23.426973] [BT_LPM] bluesleep_tx_timer_expire: Tx has been idle
[   23.433819] [BT_LPM] bluesleep_hostwake_task: hostwake line change
[   25.290158] CPU Budget: Temperature: 51 Limit state:0 item[1800000,4,1800000,4 0]
[   25.800137] CPU Budget: Temperature: 49 Limit state:0 item[1800000,4,1800000,4 0]
[   26.300124] CPU Budget: Temperature: 51 Limit state:1 item[1608000,4,1608000,4 0]
[   27.310113] CPU Budget: Temperature: 50 Limit state:0 item[1800000,4,1800000,4 0]
[   27.820104] CPU Budget: Temperature: 49 Limit state:0 item[1800000,4,1800000,4 0]
[   28.820113] CPU Budget: Temperature: 50 Limit state:1 item[1608000,4,1608000,4 0]
[   29.830138] CPU Budget: Temperature: 51 Limit state:0 item[1800000,4,1800000,4 0]
[   30.340087] CPU Budget: Temperature: 49 Limit state:0 item[1800000,4,1800000,4 0]
[   30.840071] CPU Budget: Temperature: 50 Limit state:1 item[1608000,4,1608000,4 0]
[   31.350075] CPU Budget: Temperature: 50 Limit state:0 item[1800000,4,1800000,4 0]
[   31.860115] CPU Budget: Temperature: 49 Limit state:0 item[1800000,4,1800000,4 0]
[   32.310711] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
[   32.322300] fs_mgr: check_fs(): mount(/dev/block/dm-0,/data,ext4)=0: Success
[   32.440180] fs_mgr: check_fs(): unmount(/data) succeeded
[   32.446233] fs_mgr: Running /system/bin/e2fsck on /dev/block/dm-0
[   32.492566] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
[   32.492571] 
[   32.499470] e2fsck: /dev/block/dm-0: clean, 11/276352 files, 36791/1104896 blocks
[   32.499479] 
[   32.520144] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: barrier=1,data=ordered,nomblk_io_submit,noauto_da_alloc,errors=panic
[   32.534945] fs_mgr: __mount(source=/dev/block/dm-0,target=/data,type=ext4)=0
[   32.544999] init: (Loading properties from /data/local.prop took 0.00s.)
[   32.552702] init: Unable to open persistent property directory "/data/property": No such file or directory
[   32.563852] init: Starting service 'logd-reinit'...
[   32.574873] init: Not bootcharting.
[   32.601499] logd.daemon: reinit
[   32.603511] init: Service 'logd-reinit' (pid 308) exited with status 0
[   32.610886] init: Failed to reload policy
[   32.611180] init: Starting service 'exec 2 (/system/bin/tzdatacheck)'...
[   32.628451] init: Service 'exec 2 (/system/bin/tzdatacheck)' (pid 311) exited with status 0
[   32.641041] init: property_set("ro.bt.bdaddr_path", "/data/misc/bluetooth/bdaddr") failed
[   32.650572] init: Starting service 'bootclone'...
[   32.670838] init: Service 'bootclone' (pid 314) exited with status 0
[   32.678859] init: Starting service 'netd'...
[   32.685262] init: Starting service 'debuggerd'...
[   32.692427] init: cannot find '/system/bin/debuggerd64', disabling 'debuggerd64'
[   32.700970] init: Starting service 'ril-daemon'...
[   32.707348] init: Starting service 'drm'...
[   32.713412] init: Starting service 'media'...
[   32.719407] init: Starting service 'installd'...
[   32.725956] init: cannot find '/system/bin/install-recovery.sh', disabling 'flash_recovery'
[   32.735644] init: Starting service 'keystore'...
[   32.742232] init: Starting service 'logger_private'...
[   32.749441] init: Starting service 'zygote'...
[   32.755905] init: Starting service 'gatekeeperd'...
[   32.932755] init: Starting service 'perfprofd'...
[   32.939524] init: Service 'logger_private' (pid 335) exited with status 1
[   33.360156] CPU Budget: Temperature: 50 Limit state:1 item[1608000,4,1608000,4 0]
[   33.460074] [BT_LPM] bluesleep_tx_timer_expire: Tx timer expired
[   33.466943] [BT_LPM] bluesleep_tx_timer_expire: Tx has been idle
[   33.681340] init: Service 'encrypt' (pid 218) exited with status 0
[   37.870119] CPU Budget: Temperature: 50 Limit state:0 item[1800000,4,1800000,4 0]
[   38.380121] CPU Budget: Temperature: 52 Limit state:1 item[1608000,4,1608000,4 0]
[   42.890092] CPU Budget: Temperature: 50 Limit state:0 item[1800000,4,1800000,4 0]
[   43.400069] CPU Budget: Temperature: 49 Limit state:0 item[1800000,4,1800000,4 0]
[   43.480036] [BT_LPM] bluesleep_tx_timer_expire: Tx timer expired
[   43.486817] [BT_LPM] bluesleep_tx_timer_expire: Tx has been idle
[   43.900171] CPU Budget: Temperature: 50 Limit state:1 item[1608000,4,1608000,4 0]
[   49.910234] CPU Budget: Temperature: 60 Limit state:2 item[1412000,4,1412000,4 0]
[   50.410626] CPU Budget: Temperature: 60 Limit state:1 item[1608000,4,1608000,4 0]
[   50.910235] CPU Budget: Temperature: 58 Limit state:1 item[1608000,4,1608000,4 0]
[   51.910215] CPU Budget: Temperature: 60 Limit state:2 item[1412000,4,1412000,4 0]
[   52.410263] CPU Budget: Temperature: 60 Limit state:1 item[1608000,4,1608000,4 0]
[   52.910192] CPU Budget: Temperature: 58 Limit state:1 item[1608000,4,1608000,4 0]
[   53.520105] [BT_LPM] bluesleep_tx_timer_expire: Tx timer expired
[   53.526907] [BT_LPM] bluesleep_tx_timer_expire: Tx has been idle
[   53.910205] CPU Budget: Temperature: 60 Limit state:2 item[1412000,4,1412000,4 0]
[   54.910298] CPU Budget: Temperature: 58 Limit state:1 item[1608000,4,1608000,4 0]
[   55.410306] CPU Budget: Temperature: 58 Limit state:1 item[1608000,4,1608000,4 0]
[   56.410266] CPU Budget: Temperature: 60 Limit state:2 item[1412000,4,1412000,4 0]
[   57.410209] CPU Budget: Temperature: 61 Limit state:1 item[1608000,4,1608000,4 0]
[   57.910241] CPU Budget: Temperature: 57 Limit state:1 item[1608000,4,1608000,4 0]
[   62.910153] CPU Budget: Temperature: 50 Limit state:0 item[1800000,4,1800000,4 0]
[   63.420839] CPU Budget: Temperature: 54 Limit state:1 item[1608000,4,1608000,4 0]
[   63.560042] [BT_LPM] bluesleep_tx_timer_expire: Tx timer expired
[   63.566827] [BT_LPM] bluesleep_tx_timer_expire: Tx has been idle
[   65.430099] CPU Budget: Temperature: 50 Limit state:0 item[1800000,4,1800000,4 0]
[   65.940092] CPU Budget: Temperature: 50 Limit state:1 item[1608000,4,1608000,4 0]
[   66.060102] warning: `main' uses 32-bit capabilities (legacy support in use)
[   66.450094] CPU Budget: Temperature: 50 Limit state:0 item[1800000,4,1800000,4 0]
[   66.960099] CPU Budget: Temperature: 50 Limit state:1 item[1608000,4,1608000,4 0]
[   73.600082] [BT_LPM] bluesleep_tx_timer_expire: Tx timer expired
[   73.606952] [BT_LPM] bluesleep_tx_timer_expire: Tx has been idle
[   74.550762] healthd: battery l=0 v=0 t=30.0 h=2 st=2 c=0 chg=a 1970-01-01 01:01:19.290507159 UTC
[   78.716924] request_suspend_state: wakeup (3->0) at 78716907748 (1970-01-01 01:01:23.459630578 UTC)
[   83.640053] [BT_LPM] bluesleep_tx_timer_expire: Tx timer expired
[   83.646847] [BT_LPM] bluesleep_tx_timer_expire: Tx has been idle
[   87.480087] CPU Budget: Temperature: 50 Limit state:0 item[1800000,4,1800000,4 0]
[   87.990092] CPU Budget: Temperature: 51 Limit state:1 item[1608000,4,1608000,4 0]
[   89.010086] CPU Budget: Temperature: 50 Limit state:0 item[1800000,4,1800000,4 0]
[   89.520108] CPU Budget: Temperature: 50 Limit state:1 item[1608000,4,1608000,4 0]
[   90.530142] CPU Budget: Temperature: 50 Limit state:0 item[1800000,4,1800000,4 0]
[   91.040199] CPU Budget: Temperature: 52 Limit state:1 item[1608000,4,1608000,4 0]
[   93.680104] [BT_LPM] bluesleep_tx_timer_expire: Tx timer expired
[   93.686990] [BT_LPM] bluesleep_tx_timer_expire: Tx has been idle
[   96.278013] healthd: battery l=0 v=0 t=30.0 h=2 st=2 c=0 chg=a 1970-01-01 01:01:41.020674794 UTC
[   96.667815] lowmemorykiller: lowmem_shrink: convert oom_adj to oom_score_adj:
[   96.676023] lowmemorykiller: oom_adj 0 => oom_score_adj 0
[   96.682198] lowmemorykiller: oom_adj 1 => oom_score_adj 58
[   96.688380] lowmemorykiller: oom_adj 2 => oom_score_adj 117
[   96.694781] lowmemorykiller: oom_adj 3 => oom_score_adj 176
[   96.701142] lowmemorykiller: oom_adj 9 => oom_score_adj 529
[   96.707493] lowmemorykiller: oom_adj 15 => oom_score_adj 1000
[   97.219493] acc_open
[   97.222138] acc_release
[  103.720095] [BT_LPM] bluesleep_tx_timer_expire: Tx timer expired
[  103.726950] [BT_LPM] bluesleep_tx_timer_expire: Tx has been idle
[  109.050163] CPU Budget: Temperature: 60 Limit state:2 item[1412000,4,1412000,4 0]
[  109.550121] CPU Budget: Temperature: 60 Limit state:1 item[1608000,4,1608000,4 0]
[  110.053079] CPU Budget: Temperature: 59 Limit state:1 item[1608000,4,1608000,4 0]
[  112.050247] CPU Budget: Temperature: 60 Limit state:2 item[1412000,4,1412000,4 0]
[  112.550223] CPU Budget: Temperature: 60 Limit state:1 item[1608000,4,1608000,4 0]
[  113.050197] CPU Budget: Temperature: 59 Limit state:1 item[1608000,4,1608000,4 0]
[  113.550240] CPU Budget: Temperature: 60 Limit state:2 item[1412000,4,1412000,4 0]
[  113.760110] [BT_LPM] bluesleep_tx_timer_expire: Tx timer expired
[  113.767103] [BT_LPM] bluesleep_tx_timer_expire: Tx has been idle
[  114.050248] CPU Budget: Temperature: 60 Limit state:1 item[1608000,4,1608000,4 0]
[  114.550242] CPU Budget: Temperature: 59 Limit state:1 item[1608000,4,1608000,4 0]
[  115.050219] CPU Budget: Temperature: 60 Limit state:2 item[1412000,4,1412000,4 0]
[  115.550415] CPU Budget: Temperature: 60 Limit state:1 item[1608000,4,1608000,4 0]
[  116.050213] CPU Budget: Temperature: 59 Limit state:1 item[1608000,4,1608000,4 0]
[  116.550235] CPU Budget: Temperature: 60 Limit state:2 item[1412000,4,1412000,4 0]
[  117.050239] CPU Budget: Temperature: 60 Limit state:1 item[1608000,4,1608000,4 0]
[  117.550223] CPU Budget: Temperature: 59 Limit state:1 item[1608000,4,1608000,4 0]
[  118.050187] CPU Budget: Temperature: 60 Limit state:2 item[1412000,4,1412000,4 0]
[  118.550201] CPU Budget: Temperature: 60 Limit state:1 item[1608000,4,1608000,4 0]
[  119.050190] CPU Budget: Temperature: 59 Limit state:1 item[1608000,4,1608000,4 0]
[  119.550234] CPU Budget: Temperature: 60 Limit state:2 item[1412000,4,1412000,4 0]
[  120.050226] CPU Budget: Temperature: 60 Limit state:1 item[1608000,4,1608000,4 0]
[  120.553444] CPU Budget: Temperature: 60 Limit state:2 item[1412000,4,1412000,4 0]
[  121.550098] CPU Budget: Temperature: 60 Limit state:1 item[1608000,4,1608000,4 0]
[  122.050127] CPU Budget: Temperature: 57 Limit state:1 item[1608000,4,1608000,4 0]
[  123.800103] [BT_LPM] bluesleep_tx_timer_expire: Tx timer expired
[  123.807043] [BT_LPM] bluesleep_tx_timer_expire: Tx has been idle
[  125.600593] init: Service 'adbd' is being killed...
[  125.606846] adb_release
[  125.610967] init: Service 'adbd' (pid 219) killed by signal 9
[  125.617555] init: Service 'adbd' (pid 219) killing any children in process group
[  125.626720] init: Starting service 'adbd'...
[  125.640858] adb_open
[  125.643456] mtp_bind_config
[  125.646651] ep_matches, wrn: endpoint already claimed, ep(0xc091e094, 0xe61ebe00, ep1in-bulk)
[  125.656393] ep_matches, wrn: endpoint already claimed, ep(0xc091e094, 0xe61ebe00, ep1in-bulk)
[  125.666001] ep_matches, wrn: endpoint already claimed, ep(0xc091e0e0, 0xe61ebe00, ep1out-bulk)
[  125.675760] gadget_is_softwinner_otg is not -int
[  125.681055] gadget_is_softwinner_otg is not -int
[  125.686345] adb_bind_config
[  125.689853] ep_matches, wrn: endpoint already claimed, ep(0xc091e094, 0xe61ebe00, ep1in-bulk)
[  125.699623] ep_matches, wrn: endpoint already claimed, ep(0xc091e0e0, 0xe61ebe00, ep1out-bulk)
[  125.709398] ep_matches, wrn: endpoint already claimed, ep(0xc091e094, 0xe61ebe00, ep1in-bulk)
[  125.719009] ep_matches, wrn: endpoint already claimed, ep(0xc091e0e0, 0xe61ebe00, ep1out-bulk)
[  125.728761] ep_matches, wrn: endpoint already claimed, ep(0xc091e12c, 0xe61c8900, ep2in-bulk)
[  127.550222] CPU Budget: Temperature: 60 Limit state:2 item[1412000,4,1412000,4 0]
[  128.050429] CPU Budget: Temperature: 60 Limit state:1 item[1608000,4,1608000,4 0]
[  128.550394] CPU Budget: Temperature: 59 Limit state:1 item[1608000,4,1608000,4 0]
[  130.550253] CPU Budget: Temperature: 60 Limit state:2 item[1412000,4,1412000,4 0]
[  131.050294] CPU Budget: Temperature: 60 Limit state:1 item[1608000,4,1608000,4 0]
[  131.550087] CPU Budget: Temperature: 59 Limit state:1 item[1608000,4,1608000,4 0]
[  133.840116] [BT_LPM] bluesleep_tx_timer_expire: Tx timer expired
[  133.847003] [BT_LPM] bluesleep_tx_timer_expire: Tx has been idle
[  134.548767] healthd: battery l=0 v=0 t=30.0 h=2 st=2 c=0 chg=a 1970-01-01 01:02:19.291420020 UTC
[  135.050414] CPU Budget: Temperature: 60 Limit state:2 item[1412000,4,1412000,4 0]
[  135.550165] CPU Budget: Temperature: 60 Limit state:1 item[1608000,4,1608000,4 0]
[  136.050240] CPU Budget: Temperature: 59 Limit state:1 item[1608000,4,1608000,4 0]
[  137.550294] CPU Budget: Temperature: 60 Limit state:2 item[1412000,4,1412000,4 0]
[  138.550162] CPU Budget: Temperature: 60 Limit state:1 item[1608000,4,1608000,4 0]
[  139.050194] CPU Budget: Temperature: 60 Limit state:2 item[1412000,4,1412000,4 0]
[  140.050106] CPU Budget: Temperature: 60 Limit state:1 item[1608000,4,1608000,4 0]
[  140.550154] CPU Budget: Temperature: 58 Limit state:1 item[1608000,4,1608000,4 0]
[  143.880085] [BT_LPM] bluesleep_tx_timer_expire: Tx timer expired
[  143.886962] [BT_LPM] bluesleep_tx_timer_expire: Tx has been idle
[  145.050255] CPU Budget: Temperature: 61 Limit state:2 item[1412000,4,1412000,4 0]
[  145.550274] CPU Budget: Temperature: 61 Limit state:1 item[1608000,4,1608000,4 0]
[  146.050168] CPU Budget: Temperature: 59 Limit state:1 item[1608000,4,1608000,4 0]
[  151.050077] CPU Budget: Temperature: 50 Limit state:0 item[1800000,4,1800000,4 0]
[  151.560063] CPU Budget: Temperature: 50 Limit state:1 item[1608000,4,1608000,4 0]
[  152.570071] CPU Budget: Temperature: 50 Limit state:0 item[1800000,4,1800000,4 0]
[  153.080095] CPU Budget: Temperature: 49 Limit state:0 item[1800000,4,1800000,4 0]
[  153.580132] CPU Budget: Temperature: 50 Limit state:1 item[1608000,4,1608000,4 0]
[  153.920029] [BT_LPM] bluesleep_tx_timer_expire: Tx timer expired
[  153.926855] [BT_LPM] bluesleep_tx_timer_expire: Tx has been idle
[  154.090088] CPU Budget: Temperature: 50 Limit state:0 item[1800000,4,1800000,4 0]
[  154.600077] CPU Budget: Temperature: 50 Limit state:1 item[1608000,4,1608000,4 0]
[  155.110065] CPU Budget: Temperature: 50 Limit state:0 item[1800000,4,1800000,4 0]
[  155.620068] CPU Budget: Temperature: 49 Limit state:0 item[1800000,4,1800000,4 0]
[  156.620131] CPU Budget: Temperature: 50 Limit state:1 item[1608000,4,1608000,4 0]
[  156.831339] init: Service 'bootanim' (pid 266) exited with status 0
[  157.048559] init: Starting service 'precopy'...
[  157.241596] init: Service 'precopy' (pid 2782) exited with status 0
[  159.972772] [dsm] Scene:0 "sayeye" (pid:235)
[  162.971577] CPU7: shutdown
[  162.992258] CPU5: shutdown
[  163.011646] CPU4: shutdown
[  163.171863] CPU4: Booted secondary processor
[  163.291988] CPU5: Booted secondary processor
[  163.371404] CPU7: Booted secondary processor
[  163.960054] [BT_LPM] bluesleep_tx_timer_expire: Tx timer expired
[  163.966837] [BT_LPM] bluesleep_tx_timer_expire: Tx has been idle
[  164.891596] CPU7: shutdown
[  164.911557] CPU6: shutdown
[  164.931492] CPU5: shutdown
[  164.951534] CPU4: shutdown
[  164.971421] CPU3: shutdown
[  165.091860] CPU2: shutdown
[  165.110883] CPU2: Booted secondary processor
[  165.271027] CPU3: Booted secondary processor
[  165.311020] CPU4: Booted secondary processor
[  165.350877] CPU5: Booted secondary processor
[  165.390982] CPU6: Booted secondary processor
[  165.430935] CPU7: Booted secondary processor
[  166.772303] CPU6: shutdown
[  166.791271] CPU6: Booted secondary processor
[  167.811863] CPU5: shutdown
[  167.832011] CPU4: shutdown
[  168.072022] CPU7: shutdown
[  168.130217] CPU Budget: Temperature: 50 Limit state:0 item[1800000,4,1800000,4 0]
[  168.571192] CPU4: Booted secondary processor
[  168.630760] CPU Budget: Temperature: 50 Limit state:1 item[1608000,4,1608000,4 0]
[  168.651042] CPU5: Booted secondary processor
[  168.831297] CPU7: Booted secondary processor
[  171.140297] CPU Budget: Temperature: 60 Limit state:2 item[1412000,4,1412000,4 0]
[  171.640204] CPU Budget: Temperature: 60 Limit state:1 item[1608000,4,1608000,4 0]
[  172.140249] CPU Budget: Temperature: 59 Limit state:1 item[1608000,4,1608000,4 0]
[  172.640392] CPU Budget: Temperature: 60 Limit state:2 item[1412000,4,1412000,4 0]
[  173.140273] CPU Budget: Temperature: 60 Limit state:1 item[1608000,4,1608000,4 0]
[  173.641318] CPU Budget: Temperature: 59 Limit state:1 item[1608000,4,1608000,4 0]
[  174.000114] [BT_LPM] bluesleep_tx_timer_expire: Tx timer expired
[  174.007073] [BT_LPM] bluesleep_tx_timer_expire: Tx has been idle
[  174.140234] CPU Budget: Temperature: 60 Limit state:2 item[1412000,4,1412000,4 0]
[  174.640411] CPU Budget: Temperature: 60 Limit state:1 item[1608000,4,1608000,4 0]
[  175.031576] CPU7: shutdown
[  175.051590] CPU6: shutdown
[  175.071819] CPU5: shutdown
[  175.091643] CPU4: shutdown
[  175.140148] CPU Budget: Temperature: 59 Limit state:1 item[1608000,4,1608000,4 0]
[  175.211545] CPU3: shutdown
[  175.230892] CPU3: Booted secondary processor
[  176.230951] CPU4: Booted secondary processor
[  177.350997] CPU5: Booted secondary processor
[  177.411282] CPU6: Booted secondary processor
[  177.451516] CPU7: Booted secondary processor
[  179.791926] CPU7: shutdown
[  179.811837] CPU5: shutdown
[  179.851850] CPU4: shutdown
[  180.820972] [dsm] Scene:0 "sayeye" (pid:235)
[  181.102163] CPU6: shutdown
[  181.301535] CPU2: shutdown
[  181.426285] CPU1: shutdown
[  182.025897] CPU1: Booted secondary processor
[  182.061003] CPU2: Booted secondary processor
[  182.081080] CPU4: Booted secondary processor
[  182.141291] CPU5: Booted secondary processor
[  182.181526] CPU6: Booted secondary processor
[  182.221524] CPU7: Booted secondary processor
[  184.040085] [BT_LPM] bluesleep_tx_timer_expire: Tx timer expired
[  184.046979] [BT_LPM] bluesleep_tx_timer_expire: Tx has been idle
[  187.992063] CPU6: shutdown
[  188.011859] CPU7: shutdown
[  188.031903] CPU5: shutdown
[  188.051835] CPU4: shutdown
[  188.071479] CPU3: shutdown
[  188.111540] CPU2: shutdown
[  188.570868] CPU2: Booted secondary processor
[  188.650860] CPU3: Booted secondary processor
[  189.371463] CPU4: Booted secondary processor
[  189.411087] CPU5: Booted secondary processor
[  190.640087] CPU Budget: Temperature: 50 Limit state:0 item[1800000,4,1800000,4 0]
[  190.941295] CPU6: Booted secondary processor
[  190.981482] CPU7: Booted secondary processor
[  191.140284] CPU Budget: Temperature: 50 Limit state:1 item[1608000,4,1608000,4 0]
[  192.650201] CPU Budget: Temperature: 60 Limit state:2 item[1412000,4,1412000,4 0]
[  193.081647] CPU7: shutdown
[  193.101490] CPU5: shutdown
[  193.121405] CPU4: shutdown
[  193.150074] CPU Budget: Temperature: 60 Limit state:1 item[1608000,4,1608000,4 0]
[  193.650086] CPU Budget: Temperature: 59 Limit state:1 item[1608000,4,1608000,4 0]
[  194.080022] [BT_LPM] bluesleep_tx_timer_expire: Tx timer expired
[  194.086776] [BT_LPM] bluesleep_tx_timer_expire: Tx has been idle
[  194.547680] healthd: battery l=0 v=0 t=30.0 h=2 st=2 c=0 chg=a 1970-01-01 01:03:19.290332257 UTC
[  194.771430] CPU6: shutdown
[  194.791483] CPU2: shutdown
[  194.951011] CPU2: Booted secondary processor
[  195.571286] CPU4: Booted secondary processor
[  195.650924] CPU5: Booted secondary processor
[  196.311380] CPU6: Booted secondary processor
[  196.650175] CPU Budget: Temperature: 50 Limit state:0 item[1800000,4,1800000,4 0]
[  196.687535] [dsm] Scene:0 "sayeye" (pid:235)
[  196.696653] [dsm] Scene:0 "sayeye" (pid:235)
[  196.743309] [dsm] Scene:0 "sayeye" (pid:235)
[  197.152749] CPU Budget: Temperature: 49 Limit state:0 item[1800000,4,1800000,4 0]
[  197.292091] CPU7: Booted secondary processor
[  197.660276] CPU Budget: Temperature: 52 Limit state:1 item[1608000,4,1608000,4 0]
[  198.453105] [dsm] Scene:0 "sayeye" (pid:235)
[  198.464743] [dsm] Scene:0 "sayeye" (pid:235)
[  198.487132] [dsm] Scene:0 "sayeye" (pid:235)
[  198.490151] sunxi_snddaudio_hw_params,line:62,freq_in:24576000,daudio_pcm_select:1,audio_format:1,signal_inversion:1
[  198.510596] [dsm] Scene:0 "sayeye" (pid:235)
[  198.539360] [dsm] Scene:0 "sayeye" (pid:235)
[  198.702306] CPU4: shutdown
[  198.862497] CPU6: shutdown
[  198.941364] CPU4: Booted secondary processor
[  198.981475] CPU6: Booted secondary processor
[  200.180394] CPU Budget: Temperature: 60 Limit state:2 item[1412000,4,1412000,4 0]
[  200.542005] CPU7: shutdown
[  200.561865] CPU6: shutdown

离线

#6 2019-05-16 20:00:48

晕哥
Administrator
注册时间: 2017-09-06
累计积分: 6,733

Re: 全志A83T无法进系统问题

2019-05-16_195229.png

重点排查 1, 2, 3, 4 看为什么会有这些差异,

顺便报一下 两个 eMMC的型号

是不是8G的不支持 ext_csd 命令?


比较软件这里下载: https://whycan.cn/t_1636.html

离线

#7 2019-05-16 20:24:01

MrJacky
会员
注册时间: 2019-02-26
累计积分: 8

Re: 全志A83T无法进系统问题

型号都是一样的8G,16G都在兼容性列表里啊,,应该是哪些没有设置好.

离线

#8 2019-05-16 20:31:32

晕哥
Administrator
注册时间: 2017-09-06
累计积分: 6,733

Re: 全志A83T无法进系统问题

跟踪驱动  ext_csd 命令,前后加调试语句,或试着跳过这个命令。

离线

#9 2019-05-16 20:46:45

MrJacky
会员
注册时间: 2019-02-26
累计积分: 8

Re: 全志A83T无法进系统问题

好的,我试试

离线

页脚