WhyCan Forum

人过留名,雁过留声,感谢各位朋友不离不弃地支持。 QQ: 516333132 (挖坑网/填坑网) admin@whycan.cn

您尚未登录。

#1 2017-12-16 09:38:03

daydayup
会员
注册时间: 2017-10-09
累计积分: 302

请问各路大神直接烧录荔枝派zero提供的预编译u-boot和固件,出现这个错误, 应该如何解决?

U-Boot 2017.01-rc2-00055-gc41fbfe7b5 (Jan 20 2017 - 00:39:08 +0800) Allwinner Technology

CPU:   Allwinner V3s (SUN8I 1681)
Model: Lichee Pi Zero
DRAM:  64 MiB
MMC:   SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment

Setting up a 800x480 lcd console (overscan 0x0)
dotclock: 33000kHz = 33000kHz: (1 * 3MHz * 66) / 6
In:    serial@01c28000
Out:   serial@01c28000
Err:   serial@01c28000
Net:   No ethernet found.
starting USB...
No controllers found
Hit any key to stop autoboot:  0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
reading /sun8i-v3s-licheepi-zero.dtb
8585 bytes read in 28 ms (298.8 KiB/s)
starting USB...
No controllers found
USB is stopped. Please issue 'usb start' first.
starting USB...
No controllers found
No ethernet found.
missing environment variable: pxeuuid
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/00000000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/0000000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/000000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/00000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/0000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/00
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/0
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/default-arm-sunxi
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/default-arm
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/default
No ethernet found.
Config file not found
starting USB...
No controllers found
No ethernet found.
No ethernet found.

请问各路大神直接烧录荔枝派zero提供的预编译u-boot和固件,出现这个错误, 应该如何解决?

最近编辑记录 daydayup (2017-12-16 09:38:22)

离线

#2 2017-12-16 09:42:13

晕哥
Administrator
注册时间: 2017-09-06
累计积分: 8,230

Re: 请问各路大神直接烧录荔枝派zero提供的预编译u-boot和固件,出现这个错误, 应该如何解决?

QQ20171216094202.png

执行这三条指令,药到病除:

setenv bootcmd "setenv bootm_boot_mode sec; load mmc 0:1 0x41000000 zImage; load mmc 0:1 0x41800000 sun8i-v3s-licheepi-zero-dock.dtb; bootz 0x41000000 - 0x41800000;"

setenv bootargs "console=ttyS0,115200 panic=5 mtdparts=spi32766.0:1M(uboot),64k(dtb),4M(kernel),-(rootfs) rootwait root=/dev/mmcblk0p2 earlyprintk rw  vt.global_cursor_default=0"

boot

在线

#3 2017-12-16 10:29:34

zhuacai
会员
注册时间: 2017-12-16
累计积分: 190

Re: 请问各路大神直接烧录荔枝派zero提供的预编译u-boot和固件,出现这个错误, 应该如何解决?

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.13.0-licheepi-zero+ (root@ubuntu) (gcc version 6.3.1 20170109 (Linaro GCC 6.3-2017.02)) #1 SMP Tue Dec 12 17:49:00 PST 2017
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Lichee Pi Zero with Dock
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] percpu: Embedded 16 pages/cpu @c3de6000 s33868 r8192 d23476 u65536
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 15883
[    0.000000] Kernel command line: console=ttyS0,115200 panic=5 mtdparts=spi32766.0:1M(uboot),64k(dtb),4M(kernel),-(rootfs) rootwait root=/dev/mmcblk0p2 earlyprintk rw  vt.global_cursor_default=0
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Memory: 53584K/64036K available (6144K kernel code, 217K rwdata, 1436K rodata, 1024K init, 262K bss, 10452K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xc4000000 - 0xff800000   ( 952 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc3e89000   (  62 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0700000   (7136 kB)
[    0.000000]       .init : 0xc0900000 - 0xc0a00000   (1024 kB)
[    0.000000]       .data : 0xc0a00000 - 0xc0a36680   ( 218 kB)
[    0.000000]        .bss : 0xc0a3d868 - 0xc0a7f06c   ( 263 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  RCU event tracing is enabled.
[    0.000000]  RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000008] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000021] Switching to timer-based delay loop, resolution 41ns
[    0.000186] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.000418] Console: colour dummy device 80x30
[    0.000453] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.000468] pid_max: default: 32768 minimum: 301
[    0.000595] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000613] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.001216] CPU: Testing write buffer coherency: ok
[    0.001590] /cpus/cpu@0 missing clock-frequency property
[    0.001616] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.002064] Setting up static identity map for 0x40100000 - 0x40100060
[    0.002253] Hierarchical SRCU implementation.
[    0.002765] smp: Bringing up secondary CPUs ...
[    0.002781] smp: Brought up 1 node, 1 CPU
[    0.002790] SMP: Total of 1 processors activated (48.00 BogoMIPS).
[    0.002797] CPU: All CPU(s) started in SVC mode.
[    0.003556] devtmpfs: initialized
[    0.006605] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.006884] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.006916] futex hash table entries: 256 (order: 2, 16384 bytes)
[    0.007084] pinctrl core: initialized pinctrl subsystem
[    0.007967] random: get_random_u32 called from bucket_table_alloc+0xf4/0x244 with crng_init=0
[    0.008104] NET: Registered protocol family 16
[    0.008588] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.009719] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.009738] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.023039] SCSI subsystem initialized
[    0.023332] usbcore: registered new interface driver usbfs
[    0.023400] usbcore: registered new interface driver hub
[    0.023493] usbcore: registered new device driver usb
[    0.023749] pps_core: LinuxPPS API ver. 1 registered
[    0.023759] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.023798] PTP clock support registered
[    0.024024] Advanced Linux Sound Architecture Driver Initialized.
[    0.025870] clocksource: Switched to clocksource arch_sys_counter
[    0.036974] NET: Registered protocol family 2
[    0.037568] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.037605] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[    0.037628] TCP: Hash tables configured (established 1024 bind 1024)
[    0.037763] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.037814] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.038037] NET: Registered protocol family 1
[    0.038646] RPC: Registered named UNIX socket transport module.
[    0.038665] RPC: Registered udp transport module.
[    0.038670] RPC: Registered tcp transport module.
[    0.038677] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.040778] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[    0.049754] NFS: Registering the id_resolver key type
[    0.049810] Key type id_resolver registered
[    0.049819] Key type id_legacy registered
[    0.050840] random: fast init done
[    0.053748] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    0.053772] io scheduler noop registered
[    0.053780] io scheduler deadline registered
[    0.054032] io scheduler cfq registered (default)
[    0.054045] io scheduler mq-deadline registered
[    0.054052] io scheduler kyber registered
[    0.058514] sun8i-v3s-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[    0.128575] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
[    0.131923] console [ttyS0] disabled
[    0.152194] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 36, base_baud = 1500000) is a U6_16550A
[    0.736175] console [ttyS0] enabled
[    0.743086] libphy: Fixed MDIO Bus: probed
[    0.747743] dwmac-sun8i 1c30000.ethernet: PTP uses main clock
[    0.753542] dwmac-sun8i 1c30000.ethernet: No regulator found
[    0.759311] dwmac-sun8i 1c30000.ethernet: Will use internal PHY
[    0.765464] dwmac-sun8i 1c30000.ethernet: Chain mode enabled
[    0.771167] dwmac-sun8i 1c30000.ethernet: No HW DMA feature register supported
[    0.778397] dwmac-sun8i 1c30000.ethernet: Normal descriptors
[    0.784050] dwmac-sun8i 1c30000.ethernet: RX Checksum Offload Engine supported
[    0.791274] dwmac-sun8i 1c30000.ethernet: COE Type 2
[    0.796243] dwmac-sun8i 1c30000.ethernet: TX Checksum insertion supported
[    0.803196] libphy: stmmac: probed
[    0.808508] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.815048] ehci-platform: EHCI generic platform driver
[    0.820671] ehci-platform 1c1a000.usb: EHCI Host Controller
[    0.826351] ehci-platform 1c1a000.usb: new USB bus registered, assigned bus number 1
[    0.834273] ehci-platform 1c1a000.usb: irq 26, io mem 0x01c1a000
[    0.865894] ehci-platform 1c1a000.usb: USB 2.0 started, EHCI 1.00
[    0.873069] hub 1-0:1.0: USB hub found
[    0.877036] hub 1-0:1.0: 1 port detected
[    0.881546] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.887845] ohci-platform: OHCI generic platform driver
[    0.893419] ohci-platform 1c1a400.usb: Generic Platform OHCI controller
[    0.900148] ohci-platform 1c1a400.usb: new USB bus registered, assigned bus number 2
[    0.908107] ohci-platform 1c1a400.usb: irq 27, io mem 0x01c1a400
[    0.980953] hub 2-0:1.0: USB hub found
[    0.984778] hub 2-0:1.0: 1 port detected
[    0.992382] udc-core: couldn't find an available UDC - added [g_cdc] to list of pending drivers
[    1.001961] input: 1c22800.lradc as /devices/platform/soc/1c22800.lradc/input/input0
[    1.010941] sun6i-rtc 1c20400.rtc: rtc core: registered rtc-sun6i as rtc0
[    1.017846] sun6i-rtc 1c20400.rtc: RTC enabled
[    1.022388] i2c /dev entries driver
[    1.027393] input: ns2009_ts as /devices/platform/soc/1c2ac00.i2c/i2c-0/0-0048/input/input1
[    1.036901] sunxi-wdt 1c20ca0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[    1.105921] sunxi-mmc 1c0f000.mmc: base:0xc41f8000 irq:23
[    1.165902] sunxi-mmc 1c10000.mmc: base:0xc41fc000 irq:24
[    1.172418] usbcore: registered new interface driver usbhid
[    1.178088] usbhid: USB HID core driver
[    1.183559] sun4i-codec 1c22c00.codec: ASoC: /soc/codec-analog@01c23000 not registered
[    1.191614] sun4i-codec 1c22c00.codec: Failed to register our card
[    1.200240] NET: Registered protocol family 17
[    1.204802] Key type dns_resolver registered
[    1.209334] Registering SWP/SWPB emulation handler
[    1.220967] simple-framebuffer 43e89000.framebuffer: framebuffer at 0x43e89000, 0x177000 bytes, mapped to 0xc4380000
[    1.231638] simple-framebuffer 43e89000.framebuffer: format=x8r8g8b8, mode=800x480x32, linelength=3200
[    1.248028] Console: switching to colour frame buffer device 100x30
[    1.260476] simple-framebuffer 43e89000.framebuffer: fb0: simplefb registered!
[    1.269032] usb_phy_generic usb_phy_generic.0.auto: usb_phy_generic.0.auto supply vcc not found, using dummy regulator
[    1.280414] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver
[    1.286254] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 3
[    1.294186] mmc0: host does not support reading read-only switch, assuming write-enable
[    1.303454] hub 3-0:1.0: USB hub found
[    1.307633] mmc0: new high speed SDHC card at address e624
[    1.313717] hub 3-0:1.0: 1 port detected
[    1.317933] mmcblk0: mmc0:e624 SU04G 3.69 GiB
[    1.324641] using random self ethernet address
[    1.329238] using random host ethernet address
[    1.334113]  mmcblk0: p1 p2
[    1.338898] usb0: HOST MAC 1e:69:ad:e2:7c:5f
[    1.343219] usb0: MAC 86:6f:e8:bc:ef:b5
[    1.347212] g_cdc gadget: CDC Composite Gadget, version: King Kamehameha Day 2008
[    1.354691] g_cdc gadget: g_cdc ready
[    1.360979] sun4i-codec 1c22c00.codec: Codec <-> 1c22c00.codec mapping ok
[    1.369697] sun6i-rtc 1c20400.rtc: setting system clock to 1970-01-01 00:16:21 UTC (981)
[    1.378119] vcc5v0: disabling
[    1.381096] ALSA device list:
[    1.384060]   #0: V3s Audio Codec
[    1.389582] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities
[    1.399069] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities
[    1.408987] mmc1: new high speed SDIO card at address 0001
[    1.427652] EXT4-fs (mmcblk0p2): recovery complete
[    1.432475] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[    1.440744] VFS: Mounted root (ext4 filesystem) on device 179:2.
[    1.448074] devtmpfs: mounted
[    1.452344] Freeing unused kernel memory: 1024K
[    1.458351] Starting init: /sbin/init exists but couldn't execute it (error -13)
[    1.510886] musb-hdrc musb-hdrc.1.auto: VBUS_ERROR in b_idle (80, <SessEnd), retry #0, port1 00000100
/bin/sh: can't open 'earlyprintk'
[    1.586006] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000200
[    1.586006]
[    1.595148] CPU: 0 PID: 1 Comm: sh Not tainted 4.13.0-licheepi-zero+ #1
[    1.601752] Hardware name: Allwinner sun8i Family
[    1.606489] [<c010e58c>] (unwind_backtrace) from [<c010b2b0>] (show_stack+0x10/0x14)
[    1.614239] [<c010b2b0>] (show_stack) from [<c06627fc>] (dump_stack+0x84/0x98)
[    1.621463] [<c06627fc>] (dump_stack) from [<c011b728>] (panic+0xdc/0x248)
[    1.628336] [<c011b728>] (panic) from [<c011e298>] (do_exit+0xa68/0xa98)
[    1.635034] [<c011e298>] (do_exit) from [<c011f114>] (do_group_exit+0x3c/0xd0)
[    1.642249] [<c011f114>] (do_group_exit) from [<c011f1b8>] (__wake_up_parent+0x0/0x18)
[    1.650168] Rebooting in 5 seconds..



我遇到的问题和楼主一样,按晕哥的方法解决,但又出现以上问题不能启动根文件系统,还请晕哥帮忙解决,谢谢!

离线

#4 2017-12-16 10:33:57

晕哥
Administrator
注册时间: 2017-09-06
累计积分: 8,230

Re: 请问各路大神直接烧录荔枝派zero提供的预编译u-boot和固件,出现这个错误, 应该如何解决?

[    1.458351] Starting init: /sbin/init exists but couldn't execute it (error -13)

这个问题一般出现在使用了错误的工具链生成了busybox, 导致你使用了错误的指令集。

在线

#5 2017-12-16 10:36:03

晕哥
Administrator
注册时间: 2017-09-06
累计积分: 8,230

Re: 请问各路大神直接烧录荔枝派zero提供的预编译u-boot和固件,出现这个错误, 应该如何解决?

你检查一下生成busybox是不是用了x86/x64的gcc, 而不是arm linux平台的gcc.

这个帖子: 荔枝派Zero V3s开发板入坑教程 的一楼有我编译好的uboot,zImage, rootfs下载。

在线

#6 2017-12-16 10:46:43

zhuacai
会员
注册时间: 2017-12-16
累计积分: 190

Re: 请问各路大神直接烧录荔枝派zero提供的预编译u-boot和固件,出现这个错误, 应该如何解决?

晕哥 说:

你检查一下生成busybox是不是用了x86/x64的gcc, 而不是arm linux平台的gcc.

这个帖子: 荔枝派Zero V3s开发板入坑教程 的一楼有我编译好的uboot,zImage, rootfs下载。



晕哥,我是按照 荔枝派Zero V3s开发板入坑教程 制作的文件系统,直接用buildroot-v3s-20171122.config配置文件编译,就是不知那里设置交又编译工具链!是不否能请教下那里设置交又编译工具链.

离线

#7 2017-12-16 10:57:59

晕哥
Administrator
注册时间: 2017-09-06
累计积分: 8,230

Re: 请问各路大神直接烧录荔枝派zero提供的预编译u-boot和固件,出现这个错误, 应该如何解决?

zhuacai 说:
晕哥 说:

你检查一下生成busybox是不是用了x86/x64的gcc, 而不是arm linux平台的gcc.

这个帖子: 荔枝派Zero V3s开发板入坑教程 的一楼有我编译好的uboot,zImage, rootfs下载。



晕哥,我是按照 荔枝派Zero V3s开发板入坑教程 制作的文件系统,直接用buildroot-v3s-20171122.config配置文件编译,就是不知那里设置交又编译工具链!是不否能请教下那里设置交又编译工具链.

哎,又一个被我带入坑的


看15楼:  荔枝派Zero V3s开发板入坑教程

我大概明白原因了, 应该解压缩 buildroot-v3s-20171122.zip 改名.config

在线

#8 2017-12-16 10:58:32

晕哥
Administrator
注册时间: 2017-09-06
累计积分: 8,230

Re: 请问各路大神直接烧录荔枝派zero提供的预编译u-boot和固件,出现这个错误, 应该如何解决?

看来挖坑侠不是白叫的 big_smile big_smile big_smile

在线

#9 2017-12-16 11:06:11

zhuacai
会员
注册时间: 2017-12-16
累计积分: 190

Re: 请问各路大神直接烧录荔枝派zero提供的预编译u-boot和固件,出现这个错误, 应该如何解决?

晕哥 说:
zhuacai 说:
晕哥 说:

你检查一下生成busybox是不是用了x86/x64的gcc, 而不是arm linux平台的gcc.

这个帖子: 荔枝派Zero V3s开发板入坑教程 的一楼有我编译好的uboot,zImage, rootfs下载。



晕哥,我是按照 荔枝派Zero V3s开发板入坑教程 制作的文件系统,直接用buildroot-v3s-20171122.config配置文件编译,就是不知那里设置交又编译工具链!是不否能请教下那里设置交又编译工具链.

哎,又一个被我带入坑的


看15楼:  荔枝派Zero V3s开发板入坑教程

我大概明白原因了, 应该解压缩 buildroot-v3s-20171122.zip 改名.config


我是改成了.config才编译了

离线

#10 2017-12-16 11:09:47

Wang
会员
注册时间: 2017-12-09
累计积分: 10

Re: 请问各路大神直接烧录荔枝派zero提供的预编译u-boot和固件,出现这个错误, 应该如何解决?

晕哥 说:

看来挖坑侠不是白叫的 big_smile big_smile big_smile

太多小白入坑了,晕哥应该多做些基础教程了:D

离线

#11 2017-12-16 11:12:27

晕哥
Administrator
注册时间: 2017-09-06
累计积分: 8,230

Re: 请问各路大神直接烧录荔枝派zero提供的预编译u-boot和固件,出现这个错误, 应该如何解决?

zhuacai 说:
晕哥 说:
zhuacai 说:


晕哥,我是按照 荔枝派Zero V3s开发板入坑教程 制作的文件系统,直接用buildroot-v3s-20171122.config配置文件编译,就是不知那里设置交又编译工具链!是不否能请教下那里设置交又编译工具链.

哎,又一个被我带入坑的


看15楼:  荔枝派Zero V3s开发板入坑教程

我大概明白原因了, 应该解压缩 buildroot-v3s-20171122.zip 改名.config


我是改成了.config才编译了

这就尴尬了.
1. 打开 .config, 看工具链是否真有arm ? 对比一下文件, linux下可以用meld工具,挺好用。
2. 编译的时候控制台会出现工具链信息,确认是否是gcc or arm-linux-gcc ?

在线

#12 2017-12-16 11:13:41

晕哥
Administrator
注册时间: 2017-09-06
累计积分: 8,230

Re: 请问各路大神直接烧录荔枝派zero提供的预编译u-boot和固件,出现这个错误, 应该如何解决?

Wang 说:
晕哥 说:

看来挖坑侠不是白叫的 big_smile big_smile big_smile

太多小白入坑了,晕哥应该多做些基础教程了:D

挖坑网感谢各路网友捧场!

在线

#13 2019-11-07 17:50:05

单刀
会员
注册时间: 2019-11-07
累计积分: 16

Re: 请问各路大神直接烧录荔枝派zero提供的预编译u-boot和固件,出现这个错误, 应该如何解决?

daydayup 说:

U-Boot 2017.01-rc2-00055-gc41fbfe7b5 (Jan 20 2017 - 00:39:08 +0800) Allwinner Technology

CPU:   Allwinner V3s (SUN8I 1681)
Model: Lichee Pi Zero
DRAM:  64 MiB
MMC:   SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment

Setting up a 800x480 lcd console (overscan 0x0)
dotclock: 33000kHz = 33000kHz: (1 * 3MHz * 66) / 6
In:    serial@01c28000
Out:   serial@01c28000
Err:   serial@01c28000
Net:   No ethernet found.
starting USB...
No controllers found
Hit any key to stop autoboot:  0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
reading /sun8i-v3s-licheepi-zero.dtb
8585 bytes read in 28 ms (298.8 KiB/s)
starting USB...
No controllers found
USB is stopped. Please issue 'usb start' first.
starting USB...
No controllers found
No ethernet found.
missing environment variable: pxeuuid
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/00000000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/0000000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/000000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/00000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/0000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/00
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/0
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/default-arm-sunxi
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/default-arm
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/default
No ethernet found.
Config file not found
starting USB...
No controllers found
No ethernet found.
No ethernet found.

请问各路大神直接烧录荔枝派zero提供的预编译u-boot和固件,出现这个错误, 应该如何解决?

其实最主要的问题是应该配置下u-boot里的sun8i.h(完整路径u-boot/include/configs/sun8i.h)
添加内容如下:

#define CONFIG_BOOTCOMMAND "setenv bootm_boot_mode sec; load mmc 0:1 0x41000000 zImage; load mmc 0:1 0x41800000 sun8i-v3s-licheepi-zero-dock.dtb; bootz 0x41000000 - 0x41800000;"

#define CONFIG_BOOTARGS    "console=ttyS0,115200 panic=5 mtdparts=spi32766.0:1M(uboot),64k(dtb),4M(kernel),-(rootfs) rootwait root=/dev/mmcblk0p2 earlyprintk rw  vt.global_cursor_default=0"

sun8i.h


今天刚入手荔枝派zero,搞完了spi启动,现在又搞TF启动,因此我也碰见了这问题。之前楼上在讨论是busybox的编译问题,但是既然用2楼的三条命令可以启动,那说明整个文件系统编译没有问题,否则再怎么着也启动不了。

感觉晕歌给的命令很像SPI启动的配置方式,因此就狸猫换太子,把命令修改了一下,结果还真好了。

最近编辑记录 单刀 (2019-11-07 17:50:49)

离线

页脚