感谢小智极客赠送的全志/索智S3开发板样品!小巧精致,漂亮大方! (多图预警)

晕哥 · 2019-03-10 15:14:27

购买链接:

小智极客索智全志 S3 核心板开发板Linux系统: https://item.taobao.com/item.htm?id=588502966831
小智极客索智/全志S3全功能底板: https://item.taobao.com/item.htm?id=588722094008
全志/索智S3芯片零售,内置128MB DDR3内存: https://item.taobao.com/item.htm?id=588754350002

QQ交流群: 202900925

全志V3s手册V1.0: Allwinner_V3s_Datasheet_V1.0.pdf
全志S3手册V0.2: Allwinner_S3_Datasheet_V0_2.pdf (索智S3手册)

参考链接: 编译索智(Sochip) S3 SDK (zeta)

2019-04-08 更新:
-------------------------------------------------
固件下载(主线uboot + 主线 linux 4.13): XiaoZhi_S3_Simple_V1_Pack_20190408.7z

2019-04-10 更新:
-------------------------------------------------
固件下载(主线uboot + 主线 linux 4.13)uart0, uart2两个版本: XiaoZhi_S3_Simple_V1_Pack_20190410.7z

源码地址: https://github.com/qq516333132/u-boot/tree/XiaoZhi_S3_Simple_V1

晕哥 · 2019-03-10 15:15:47

...

晕哥 · 2019-03-10 15:15:49

占位

晕哥 · 2019-03-10 15:15:51

占位

晕哥 · 2019-03-10 15:15:53

晕哥 · 2019-03-10 15:15:55

晕哥 · 2019-03-10 16:13:48

晕哥 · 2019-03-10 16:35:04

mango 说：

狂顶，改天拍一个过来玩。
我们的S3板子还得等段时间，在和seeed一起搞个全球首发的秘密项目，压力太大。

坐等秘密项目被公开。

晕哥 · 2019-03-11 17:19:49

焊上按键,烧录方便多了。

焊上排针，串口输出正常。

用 sunxi-fel 测试烧录，也正常。

晕哥 · 2019-03-11 18:11:03

把荔枝派的 u-boot 弄到 S3 跑跑:

参考链接: https://whycan.cn/t_561.html

1. 克隆源码: git clone https://github.com/Lichee-Pi/u-boot.git -b v3s-spi-experimental

2. ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- make LicheePi_Zero_defconfig (默认)

3. 修改 arch/arm/mach-sunxi/dram_sun8i_h3.c:

#ifdef CONFIG_SUNXI_H3_DRAM_DDR2
u8 bank_bits;
#endif

改为:

u8 bank_bits;

4. 修改 board/sunxi/Kconfig
删除第 138 行:

select SUNXI_H3_DRAM_DDR2

5. .config 文件删除以下行: CONFIG_SUNXI_H3_DRAM_DDR2

可以用 sunxi-fel 烧录到 S3 板子,

调试串口是 PB8, PB9 也就是示意图上面 B6, C6

晕哥 · 2019-03-11 23:10:40

修改 drivers/video/sunxi_display.c

for (pin = SUNXI_GPE(0); pin <= SUNXI_GPE(24); pin++) {
if (pin >= SUNXI_GPE(20) && pin <= SUNXI_GPE(22))
continue; /* These pins are not LCD */
sunxi_gpio_set_cfgpin(pin, SUN8I_V3S_GPE_LCD);
}

改为:

for (pin = SUNXI_GPD(0); pin <= SUNXI_GPD(21); pin++) {
sunxi_gpio_set_cfgpin(pin, SUNXI_GPD_LCD0);
}

可以点亮 LCD 屏了!

晕哥 · 2019-03-13 08:43:01

外壳建模完成！这是今天凌晨三点半，勤劳的@小智科技带着黑圆圈发给我的。

不知道是否能把 IO 口引脚丝印做上去?

晕哥 · 2019-04-08 08:51:08

安装 arm gcc 浮点数工具链:

sudo apt-get install gcc-arm-linux-gnueabihf

编译 S3 u-boot 流程:

git clone https://github.com/qq516333132/u-boot.git -b XiaoZhi_S3_Simple_V1

###启用 4.3 寸配置 ###
ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- make XiaoZhi_S3_Simple_V1_480x272LCD_defconfig
###启用 5.0 寸配置 ###
ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- make XiaoZhi_S3_Simple_V1_800x480LCD_defconfig
###编译###
ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- make

修改记录:
https://github.com/qq516333132/u-boot/commits/XiaoZhi_S3_Simple_V1
https://github.com/qq516333132/u-boot/commit/404c4f2d1a8c88c8db338111173683043d3ba6cf
https://github.com/qq516333132/u-boot/commit/c14c5d029f10bf6a365a7f128b57ec0deb8b176b
https://github.com/qq516333132/u-boot/commit/b63ce45082d5b2762dbdb0d90000319c45ab06e2

diff 文件:
root@test4:/opt/u-boot# git diff dd6e8740dc2dc24d64c6ee62250330a174b16607 b63ce45082d5b2762dbdb0d90000319c45ab06e2

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 469dd71..24ac190 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -282,6 +282,8 @@ dtb-$(CONFIG_MACH_SUN8I_H3) += \
        sun8i-h3-nanopi-neo.dtb
 dtb-$(CONFIG_MACH_SUN8I_V3S) += \
        sun8i-v3s-licheepi-zero.dtb
+dtb-$(CONFIG_MACH_SUN8I_S3) += \
+       sun8i-v3s-licheepi-zero.dtb
 dtb-$(CONFIG_MACH_SUN50I) += \
        sun50i-a64-pine64-plus.dtb \
        sun50i-a64-pine64.dtb
diff --git a/arch/arm/include/asm/arch-sunxi/clock_sun6i.h b/arch/arm/include/asm/arch-sunxi/clock_sun6i.h
index 5bbc869..6aadac8 100644
--- a/arch/arm/include/asm/arch-sunxi/clock_sun6i.h
+++ b/arch/arm/include/asm/arch-sunxi/clock_sun6i.h
@@ -451,7 +451,7 @@ struct sunxi_ccm_reg {
 /* CCM bits common to all Display Engine 2.0 clock ctrl regs */
 #define CCM_DE2_CTRL_M(n)              ((((n) - 1) & 0xf) << 0)
 #define CCM_DE2_CTRL_PLL_MASK          (3 << 24)
-#ifndef CONFIG_MACH_SUN8I_V3S
+#if !defined(CONFIG_MACH_SUN8I_V3S) && !defined(CONFIG_MACH_SUN8I_S3)
 #define CCM_DE2_CTRL_PLL6_2X           (0 << 24)
 #define CCM_DE2_CTRL_PLL10             (1 << 24)
 #else
diff --git a/arch/arm/include/asm/arch-sunxi/pwm.h b/arch/arm/include/asm/arch-sunxi/pwm.h
index c83ca37..f061383 100644
--- a/arch/arm/include/asm/arch-sunxi/pwm.h
+++ b/arch/arm/include/asm/arch-sunxi/pwm.h
@@ -31,7 +31,7 @@
 #define SUNXI_PWM_MUX                  SUN8I_GPH_PWM
 #endif

-#if defined CONFIG_MACH_SUN8I_V3S
+#if defined CONFIG_MACH_SUN8I_V3S || defined CONFIG_MACH_SUN8I_S3
 #define SUNXI_PWM_PIN0                 SUNXI_GPB(4)
 #define SUNXI_PWM_MUX                  SUN8I_V3S_GPB_PWM
 #endif
diff --git a/arch/arm/mach-sunxi/board.c b/arch/arm/mach-sunxi/board.c
index 7a55ee3..b463653 100644
--- a/arch/arm/mach-sunxi/board.c
+++ b/arch/arm/mach-sunxi/board.c
@@ -110,7 +110,7 @@ static int gpio_init(void)
        sunxi_gpio_set_cfgpin(SUNXI_GPB(9), SUN8I_A83T_GPB_UART0);
        sunxi_gpio_set_cfgpin(SUNXI_GPB(10), SUN8I_A83T_GPB_UART0);
        sunxi_gpio_set_pull(SUNXI_GPB(10), SUNXI_GPIO_PULL_UP);
-#elif CONFIG_CONS_INDEX == 1 && defined(CONFIG_MACH_SUN8I_V3S)
+#elif CONFIG_CONS_INDEX == 1 && (defined(CONFIG_MACH_SUN8I_V3S) || defined(CONFIG_MACH_SUN8I_S3))
        sunxi_gpio_set_cfgpin(SUNXI_GPB(8), SUN8I_V3S_GPB_UART0);
        sunxi_gpio_set_cfgpin(SUNXI_GPB(9), SUN8I_V3S_GPB_UART0);
        sunxi_gpio_set_pull(SUNXI_GPB(9), SUNXI_GPIO_PULL_UP);
diff --git a/arch/arm/mach-sunxi/cpu_info.c b/arch/arm/mach-sunxi/cpu_info.c
index 15f1e0e..34bcb5e 100644
--- a/arch/arm/mach-sunxi/cpu_info.c
+++ b/arch/arm/mach-sunxi/cpu_info.c
@@ -87,7 +87,7 @@ int print_cpuinfo(void)
        printf("CPU:   Allwinner A83T (SUN8I %04x)\n", sunxi_get_sram_id());
 #elif defined CONFIG_MACH_SUN8I_H3
        printf("CPU:   Allwinner H3 (SUN8I %04x)\n", sunxi_get_sram_id());
-#elif defined CONFIG_MACH_SUN8I_V3S
+#elif defined CONFIG_MACH_SUN8I_V3S || defined CONFIG_MACH_SUN8I_S3
        printf("CPU:   Allwinner V3s (SUN8I %04x)\n", sunxi_get_sram_id());
 #elif defined CONFIG_MACH_SUN9I
        puts("CPU:   Allwinner A80 (SUN9I)\n");
diff --git a/arch/arm/mach-sunxi/dram_sun8i_h3.c b/arch/arm/mach-sunxi/dram_sun8i_h3.c
index a48320e..ec220f2 100644
--- a/arch/arm/mach-sunxi/dram_sun8i_h3.c
+++ b/arch/arm/mach-sunxi/dram_sun8i_h3.c
@@ -22,9 +22,9 @@ struct dram_para {
        u8 bus_width;
        u8 dual_rank;
        u8 row_bits;
-#ifdef CONFIG_SUNXI_H3_DRAM_DDR2
+//#ifdef CONFIG_SUNXI_H3_DRAM_DDR2
        u8 bank_bits;
-#endif
+//#endif
 };

 static inline int ns_to_t(int nanoseconds)
diff --git a/board/sunxi/Kconfig b/board/sunxi/Kconfig
index a451f47..4437c01 100644
--- a/board/sunxi/Kconfig
+++ b/board/sunxi/Kconfig
@@ -139,6 +139,17 @@ config MACH_SUN8I_V3S
        select SUNXI_DE2
        select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT

+config MACH_SUN8I_S3
+       bool "sun8i (Allwinner S3)"
+       select CPU_V7
+       select CPU_V7_HAS_NONSEC
+       select CPU_V7_HAS_VIRT
+       select SUNXI_GEN_SUN6I
+       select SUPPORT_SPL
+       select SUNXI_H3_DW_DRAM
+       select SUNXI_DE2
+       select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
+
 config MACH_SUN9I
        bool "sun9i (Allwinner A80)"
        select CPU_V7
@@ -155,7 +166,7 @@ endchoice
 # The sun8i SoCs share a lot, this helps to avoid a lot of "if A23 || A33"
 config MACH_SUN8I
        bool
-       default y if MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_H3 || MACH_SUN8I_A83T || MACH_SUN8I_V3S
+       default y if MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_H3 || MACH_SUN8I_A83T || MACH_SUN8I_V3S || MACH_SUN8I_S3

 config DRAM_TYPE
        int "sunxi dram type"
diff --git a/configs/XiaoZhi_S3_Simple_V1_480x272LCD_defconfig b/configs/XiaoZhi_S3_Simple_V1_480x272LCD_defconfig
new file mode 100644
index 0000000..7192ee7
--- /dev/null
+++ b/configs/XiaoZhi_S3_Simple_V1_480x272LCD_defconfig
@@ -0,0 +1,27 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+# CONFIG_ARMV7_NONSEC is not set
+CONFIG_MACH_SUN8I_S3=y
+CONFIG_DRAM_CLK=360
+CONFIG_DRAM_ZQ=14779
+CONFIG_VIDEO_LCD_MODE="x:480,y:272,depth:18,pclk_khz:10000,le:42,ri:8,up:11,lo:4,hs:1,vs:1,sync:3,vmode:0"CONFIG_VIDEO_LCD_MODE="x:480,y:272,depth:18,pclk_khz:10000,le:42,ri:8,up:11,lo:4,hs:1,vs:1,sync:3,vmode:0"CONFIG_VIDEO_LCD_MODE="x:480,y:272,depth:18,pclk_khz:10000,le:42,ri:8,up:11,lo:4,hs:1,vs:1,sync:3,vmode:0"CONFIG_VIDEO_LCD_MODE="x:480,y:272,depth:18,pclk_khz:10000,le:42,ri:8,up:11,lo:4,hs:1,vs:1,sync:3,vmode:0"CONFIG_VIDEO_LCD_MODE="x:480,y:272,depth:18,pclk_khz:10000,le:42,ri:8,up:11,lo:4,hs:1,vs:1,sync:3,vmode:0"
+CONFIG_VIDEO_LCD_BL_PWM="PB4"
+# CONFIG_VIDEO_LCD_BL_PWM_ACTIVE_LOW is not set
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-v3s-licheepi-zero"
+# CONFIG_CONSOLE_MUX is not set
+CONFIG_SPL=y
+CONFIG_CMD_BOOTMENU=y
+# CONFIG_CMD_IMLS is not set
+CONFIG_CMD_MEMINFO=y
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_SF=y
+CONFIG_CMD_SPI=y
+# CONFIG_CMD_FPGA is not set
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_WINBOND=y
+CONFIG_SPL_SPI_SUNXI=y
+# CONFIG_NETDEVICES is not set
+CONFIG_DM_SPI=y
+CONFIG_SUNXI_SPI=y
+CONFIG_OF_LIBFDT_OVERLAY=y
diff --git a/configs/XiaoZhi_S3_Simple_V1_800x480LCD_defconfig b/configs/XiaoZhi_S3_Simple_V1_800x480LCD_defconfig
new file mode 100644
index 0000000..53245de
--- /dev/null
+++ b/configs/XiaoZhi_S3_Simple_V1_800x480LCD_defconfig
@@ -0,0 +1,27 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+# CONFIG_ARMV7_NONSEC is not set
+CONFIG_MACH_SUN8I_S3=y
+CONFIG_DRAM_CLK=360
+CONFIG_DRAM_ZQ=14779
+CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:87,ri:40,up:31,lo:13,hs:1,vs:1,sync:3,vmode:0"
+CONFIG_VIDEO_LCD_BL_PWM="PB4"
+# CONFIG_VIDEO_LCD_BL_PWM_ACTIVE_LOW is not set
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-v3s-licheepi-zero"
+# CONFIG_CONSOLE_MUX is not set
+CONFIG_SPL=y
+CONFIG_CMD_BOOTMENU=y
+# CONFIG_CMD_IMLS is not set
+CONFIG_CMD_MEMINFO=y
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_SF=y
+CONFIG_CMD_SPI=y
+# CONFIG_CMD_FPGA is not set
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_WINBOND=y
+CONFIG_SPL_SPI_SUNXI=y
+# CONFIG_NETDEVICES is not set
+CONFIG_DM_SPI=y
+CONFIG_SUNXI_SPI=y
+CONFIG_OF_LIBFDT_OVERLAY=y
diff --git a/drivers/video/sunxi_display.c b/drivers/video/sunxi_display.c
index 7049a3c..06ccb01 100644
--- a/drivers/video/sunxi_display.c
+++ b/drivers/video/sunxi_display.c
@@ -525,7 +525,7 @@ static void sunxi_composer_init(void)
        struct sunxi_ccm_reg * const ccm =
                (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;

-#ifndef CONFIG_MACH_SUN8I_V3S
+#if !defined(CONFIG_MACH_SUN8I_V3S) && !defined(CONFIG_MACH_SUN8I_S3)
        clock_set_pll10(432000000);

        /* Set DE parent to pll10 */
@@ -905,7 +905,7 @@ static void sunxi_lcdc_tcon0_mode_set(const struct ctfb_res_modes *mode,
                (struct sunxi_lcdc_reg *)SUNXI_LCD0_BASE;
        int bp, clk_delay, clk_div, clk_double, pin, total, val;

-#ifndef CONFIG_MACH_SUN8I_V3S
+#if !defined(CONFIG_MACH_SUN8I_V3S) && !defined(CONFIG_MACH_SUN8I_S3)
 #if defined CONFIG_MACH_SUN8I && defined CONFIG_VIDEO_LCD_IF_LVDS
        for (pin = SUNXI_GPD(18); pin <= SUNXI_GPD(27); pin++) {
 #else
@@ -921,13 +921,17 @@ static void sunxi_lcdc_tcon0_mode_set(const struct ctfb_res_modes *mode,
                sunxi_gpio_set_drv(pin, 3);
 #endif
        }
-#else /* CONFIG_MACH_SUN8I_V3S */
+#elif defined CONFIG_MACH_SUN8I_V3S
        for (pin = SUNXI_GPE(0); pin <= SUNXI_GPE(24); pin++) {
                if (pin >= SUNXI_GPE(20) && pin <= SUNXI_GPE(22))
                        continue; /* These pins are not LCD */
                sunxi_gpio_set_cfgpin(pin, SUN8I_V3S_GPE_LCD);
        }
-#endif /* !CONFIG_MACH_SUN8I_V3S */
+#elif defined CONFIG_MACH_SUN8I_S3
+       for (pin = SUNXI_GPD(0); pin <= SUNXI_GPD(21); pin++) {
+               sunxi_gpio_set_cfgpin(pin, SUNXI_GPD_LCD0);
+           }
+#endif

        sunxi_lcdc_pll_set(0, mode->pixclock_khz, &clk_div, &clk_double);

diff --git a/include/configs/sun8i.h b/include/configs/sun8i.h
index 6ac42ac..b8454ba 100644
--- a/include/configs/sun8i.h
+++ b/include/configs/sun8i.h
@@ -21,7 +21,7 @@
        #define CONFIG_SUNXI_USB_PHYS   4
 #elif defined CONFIG_MACH_SUN8I_A83T
        #define CONFIG_SUNXI_USB_PHYS   3
-#elif defined CONFIG_MACH_SUN8I_V3S
+#elif (defined CONFIG_MACH_SUN8I_V3S) || (defined CONFIG_MACH_SUN8I_S3)
        #define CONFIG_SUNXI_USB_PHYS   1
 #else
        #define CONFIG_SUNXI_USB_PHYS   2
diff --git a/include/configs/sunxi-common.h b/include/configs/sunxi-common.h
index fcecd0b..2874cef 100644
--- a/include/configs/sunxi-common.h
+++ b/include/configs/sunxi-common.h
@@ -77,7 +77,7 @@
 #define CONFIG_SYS_SDRAM_BASE          0x40000000
 #define CONFIG_SYS_LOAD_ADDR           0x41000000 /* default load address */
 /* V3s do not have enough memory to place code at 0x4a000000 */
-#ifndef CONFIG_MACH_SUN8I_V3S
+#if !defined(CONFIG_MACH_SUN8I_V3S) && !defined(CONFIG_MACH_SUN8I_S3)
 #define CONFIG_SYS_TEXT_BASE           0x4a000000
 #else
 #define CONFIG_SYS_TEXT_BASE           0x42e00000
@@ -153,7 +153,7 @@
 #define CONFIG_SYS_MMC_MAX_DEVICE      4
 #endif

-#ifndef CONFIG_MACH_SUN8I_V3S
+#if !defined(CONFIG_MACH_SUN8I_V3S) && !defined(CONFIG_MACH_SUN8I_S3)
 /* 64MB of malloc() pool */
 #define CONFIG_SYS_MALLOC_LEN          (CONFIG_ENV_SIZE + (64 << 20))
 #else
@@ -303,7 +303,7 @@ extern int soft_i2c_gpio_scl;
  * The amount of RAM to keep free at the top of RAM when relocating u-boot,
  * to use as framebuffer. This must be a multiple of 4096.
  */
-#ifndef CONFIG_MACH_SUN8I_V3S
+#if !defined(CONFIG_MACH_SUN8I_V3S) && !defined(CONFIG_MACH_SUN8I_S3)
 #define CONFIG_SUNXI_MAX_FB_SIZE (16 << 20)
 #else
 #define CONFIG_SUNXI_MAX_FB_SIZE (2 << 20)
@@ -410,7 +410,7 @@ extern int soft_i2c_gpio_scl;
  * 32M uncompressed kernel, 16M compressed kernel, 1M fdt,
  * 1M script, 1M pxe and the ramdisk at the end.
  */
-#ifndef CONFIG_MACH_SUN8I_V3S
+#if !defined(CONFIG_MACH_SUN8I_V3S) && !defined(CONFIG_MACH_SUN8I_S3)
 #define BOOTM_SIZE     __stringify(0xa000000)
 #define KERNEL_ADDR_R  __stringify(SDRAM_OFFSET(2000000))
 #define FDT_ADDR_R     __stringify(SDRAM_OFFSET(3000000))
@@ -440,7 +440,7 @@ extern int soft_i2c_gpio_scl;
        "pxefile_addr_r=" PXEFILE_ADDR_R "\0" \
        "ramdisk_addr_r=" RAMDISK_ADDR_R "\0"

-#ifndef CONFIG_MACH_SUN8I_V3S
+#if !defined(CONFIG_MACH_SUN8I_V3S) && !defined(CONFIG_MACH_SUN8I_S3)
 #define DFU_ALT_INFO_RAM \
        "dfu_alt_info_ram=" \
        "kernel ram " KERNEL_ADDR_R " 0x1000000;" \

晕哥 · 2019-04-08 15:17:29

https://github.com/qq516333132/u-boot/commits/XiaoZhi_S3_Simple_V1_BootCmdArgs

https://github.com/qq516333132/u-boot/commit/b9f440d625d727205970e93aace9639e7b23605f

https://github.com/qq516333132/u-boot/blob/XiaoZhi_S3_Simple_V1_BootCmdArgs/include/configs/sun8i.h

新建了一个 XiaoZhi_S3_Simple_V1_BootCmdArgs 分支,

在 include/configs/sun8i.h 添加 :

#undef CONFIG_BOOTCOMMAND
#undef CONFIG_BOOTARGS

#ifndef CONFIG_BOOTCOMMAND
#define CONFIG_BOOTCOMMAND    "sf probe 0 50000000;sf read 0x41800000 0x100000 0x4000;sf read 0x41000000 0x110000 0x500000; bootz 0x41000000 - 0x41800000"
#endif

#ifndef CONFIG_BOOTARGS
#define CONFIG_BOOTARGS       "console=ttyS0,115200 earlyprintk panic=5 rootwait mtdparts=spi32766.0:992k(uboot)ro,32k(env)ro,64k(dtb)ro,5M(kernel)ro,-(rootfs) root=31:04 rw rootfstype=jffs2"
#endif

zImage 和 rootfs 按照 V3s 的套路编译生成即可。

固件下载(主线uboot + 主线 linux 4.13): XiaoZhi_S3_Simple_V1_Pack_20190408.7z

晕哥 · 2019-04-08 17:42:51

https://github.com/Lichee-Pi/u-boot/commits/v3s-spi-experimental/common/Kconfig

https://github.com/Lichee-Pi/u-boot/commits/nano-v2018.01/common/Kconfig

原来是因为合并的版本不同，导致荔枝派 V3s 和 f1c100s 的 u-boot 表现有差异,
f1c100s 的 u-boot 可以通过 menuconfig 配置 bootargs 和 bootcmd,
而 V3s 的不可以。

晕哥 · 2019-04-18 21:12:32

zhenfanhei 说：

2000块的开发板上有没有？谁见过?

widora 的老板 -- mango 买了

晕哥 · 2019-04-25 16:07:18

yytyu 说：

请问下S3 sdk包运行频率是多少，内存带宽是多少位的

我跑的是主线Linux,默认是1.008GHz

晕哥 · 2019-05-15 11:05:13

as86455011 说：

晕哥说：
https://whycan.cn/files/members/3/QQ20190311175226.jpg
焊上按键,烧录方便多了。

https://whycan.cn/files/members/3/QQ20190311164816.jpg
焊上排针，串口输出正常。
用 sunxi-fel 测试烧录，也正常。

请教一下，这个fel模式是通过哪个管脚进入的？

1. 不插TF卡或 TF卡不能启动系统，那短路 SPI FLASH 的 CLK 引脚到 GND，再插入USB线即可。
2. 制作一个特殊的 TF卡: https://whycan.cn/t_2429.html

制作一个特殊的TF卡系统，插入即进入 fel, 这样不用短路也能烧录:
http://linux-sunxi.org/FEL
wget https://github.com/linux-sunxi/sunxi-tools/raw/master/bin/fel-sdboot.sunxi
dd if=fel-sdboot.sunxi of=/dev/sdX bs=1024 seek=8 ####sdX替换成你的TF卡实际磁盘设备

强烈建议用第二种，省得去插线拔线。

晕哥 · 2019-10-14 09:20:41

这批卖完了，刚刚问了店主，过段时间有新品。

晕哥 · 2019-11-17 17:34:33

达克罗德说：

买了新板子，请问有对应主线源码吗？晕哥用的是是索智的SDK吧，

这两天我打个主线 SDK 的包吧.

WhyCan Forum(哇酷开发者社区)

楼主 #1 2019-03-10 15:14:27 分享评论

感谢小智极客赠送的全志/索智S3开发板样品!小巧精致,漂亮大方! (多图预警)

楼主 #2 2019-03-10 15:15:47 分享评论

Re: 感谢小智极客赠送的全志/索智S3开发板样品!小巧精致,漂亮大方! (多图预警)

楼主 #3 2019-03-10 15:15:49 分享评论

Re: 感谢小智极客赠送的全志/索智S3开发板样品!小巧精致,漂亮大方! (多图预警)

楼主 #4 2019-03-10 15:15:51 分享评论

Re: 感谢小智极客赠送的全志/索智S3开发板样品!小巧精致,漂亮大方! (多图预警)

楼主 #5 2019-03-10 15:15:53 分享评论

Re: 感谢小智极客赠送的全志/索智S3开发板样品!小巧精致,漂亮大方! (多图预警)

楼主 #6 2019-03-10 15:15:55 分享评论

Re: 感谢小智极客赠送的全志/索智S3开发板样品!小巧精致,漂亮大方! (多图预警)

楼主 #7 2019-03-10 16:13:48 分享评论

Re: 感谢小智极客赠送的全志/索智S3开发板样品!小巧精致,漂亮大方! (多图预警)

楼主 #12 2019-03-10 16:35:04 分享评论

Re: 感谢小智极客赠送的全志/索智S3开发板样品!小巧精致,漂亮大方! (多图预警)

楼主 #18 2019-03-11 17:19:49 分享评论

Re: 感谢小智极客赠送的全志/索智S3开发板样品!小巧精致,漂亮大方! (多图预警)

楼主 #19 2019-03-11 18:11:03 分享评论

Re: 感谢小智极客赠送的全志/索智S3开发板样品!小巧精致,漂亮大方! (多图预警)

楼主 #21 2019-03-11 23:10:40 分享评论

Re: 感谢小智极客赠送的全志/索智S3开发板样品!小巧精致,漂亮大方! (多图预警)

楼主 #30 2019-03-13 08:43:01 分享评论

Re: 感谢小智极客赠送的全志/索智S3开发板样品!小巧精致,漂亮大方! (多图预警)

楼主 #33 2019-04-08 08:51:08 分享评论

Re: 感谢小智极客赠送的全志/索智S3开发板样品!小巧精致,漂亮大方! (多图预警)

楼主 #35 2019-04-08 15:17:29 分享评论

Re: 感谢小智极客赠送的全志/索智S3开发板样品!小巧精致,漂亮大方! (多图预警)

楼主 #36 2019-04-08 17:42:51 分享评论

Re: 感谢小智极客赠送的全志/索智S3开发板样品!小巧精致,漂亮大方! (多图预警)

楼主 #40 2019-04-18 21:12:32 分享评论

Re: 感谢小智极客赠送的全志/索智S3开发板样品!小巧精致,漂亮大方! (多图预警)

楼主 #44 2019-04-25 16:07:18 分享评论

Re: 感谢小智极客赠送的全志/索智S3开发板样品!小巧精致,漂亮大方! (多图预警)

楼主 #48 2019-05-15 11:05:13 分享评论

Re: 感谢小智极客赠送的全志/索智S3开发板样品!小巧精致,漂亮大方! (多图预警)

楼主 #53 2019-10-14 09:20:41 分享评论

Re: 感谢小智极客赠送的全志/索智S3开发板样品!小巧精致,漂亮大方! (多图预警)

楼主 #60 2019-11-17 17:34:33 分享评论

Re: 感谢小智极客赠送的全志/索智S3开发板样品!小巧精致,漂亮大方! (多图预警)

页脚